- ページ 10

アンプ Pioneer A-333のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Pioneer A-333 13 ページ。 Stereo amp
Pioneer A-333 にも：取扱説明書 (13 ページ), サービスマニュアル (26 ページ)

ページを印刷する

OPERATIONS

BEFORE BEGINNING OPERATIONS

Set the controls and switches as follows: See page 3.

1. Set the POWER switch @ to ON.

Press the SPEAKERS A selector switch 6. SPEAKERS

B selector switch (3) or both switches.

Set the BALANCE control @ to the center position.

4. Set the DIRECT switch @ to OFF.

PLAYBACK PROCEDURES

Set the INPUT SELECTOR switch [5] to the desired

playback source.

For playback with the equipment connected to the LINE

terminals: Set to [LINE].

°® For reception of an AM/FM broadcast: Set to [TUNER].

For playback of a record: Set to [PHONO].

Set the PHONO

SELECTOR switch @ to MM ( @

jor

MC ( =

) according to the type of cartridge being used.

(A-443 only)

For playback of a compact disc: Set to [CD]

For playback of a tape: Set to [DAT/TAPE 1] or [TAPE 2].

Operate the equipment to begin playback.

Adjust playback volume with the VOLUME control @

on this unit.

RECORDING TAPES:

Select

the

recording

equipment

with

the

REC

SELECTOR switch @.

® When

set to SOURCE,

the signals

from the device

connected

to the terminals

of the selected

input are

recorded. (To record signals from the device connected

to the PHONO or LINE terminals, set the REC SELECTOR

switch to SOURCE and set the INPUT SELECTOR switch

to PHONO or LINE.)

Recording is impossible when the switch is set to OFF.

NOTE:

When REC SELECTOR switch is set to a position other than SOURCE

or OFF, the equipment selected by the REC SELECTOR switch can

be recorded

from,

irrespective

of the settings

of the INPUT

SELECTOR and DIRECT switches.

Begin recording by operating the recording equipment

and tape deck.

Refer to the operating instructions for your tape deck for

proper operating procedures.

MONITORING

WHILE RECORDING

On a 3-head tape deck, sound can be concurrently heard

while recording on tape. SELECTOR operation of checking

the sound quality and recording level is called '"'monitoring.'""

For monitoring, the INPUT SELECTOR

switch of this unit

must be set to the tape deck on which recording is being

done,

DAT/TAPE

1 terminals: Set to DAT/TAPE

When

recording with the tape deck connected

to the

TAPE 2 terminals: Set to TAPE 2.

NOTE:

When recording from the PHONO or LINE source, recording monitor

is not possible,

COPYING TAPES:

When two decks are used {or when using double cassette

deck), you can record the sounds from one deck onto the

other,

Application examples:

a tape copy with contents

identical to the

original tape.

e To edit a recording of an FM broadcast in order to cut

out

unwanted

commercials,

recording

only

desired

material onto another tape.

When using two tape decks

Load

tapes

for

playback

(pre-recorded

tape)

and

recording (blank tape} into the respective tape decks.

Select the copying direction with the REC SELECTOR

switch

@ .

® When copying from the tape deck of the DAT/TAPE

terminals to the tape deck of the TAPE 2 terminals: Set

to 12.

e When

copying

from

the tape

deck

of the TAPE

terminals to the tape deck of the DAT/TAPE 1 terminals:

Set to 21.

NOTE:

The tape input selected with the REC SELECTOR switch can be

copied, regardless of the settings of INPUT SELECTOR and DIRECT

switches.

3. Operate the tape decks to begin copying.

Set the tape deck with the original (playback) tape to the

playback mode, and set the tape deck with the blank tape

to the recording mode.

Playback using a graphic equalizer

graphic equalizer connected to the ADAPTOR terminais.

However, the graphic equalizer is bypassed when the

DIRECT switch is ON.

NOTE:

Be sure to perform this operation with the adaptor component power

switch in the ON position.

Even

when

not using the adaptor

component,

its power switch must be left ON. If the adaptor

component is switched OFF, no sound will be produced, or the

playback sound will be distorted.