- ページ 3

アンプ Pioneer GM-3000TのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Pioneer GM-3000T 6 ページ。 Bridgeable power amplifier
Pioneer GM-3000T にも：オーナーズマニュアル (8 ページ), サービスマニュアル (19 ページ)

ページを印刷する

Connecting the Unit

Connecting the Speaker wires

The speaker output mode can be two-channel (stereo) or one-channel

(mono). Connect the speaker leads to suit the mode according to the figures

shown below.

• Do not connect both the RCA input and the speaker input at the same time.

Two-channel mode (stereo)

(Right)

Speaker

(Left)

One-channel mode (mono)

Speaker (Mono)

Installation

Example of installation on the floor

CAUTION

mat or on the chassis

• Do not install in:

—Places where it could injure the driver or pas-

sengers if the vehicle stops suddenly.

1. Place the amplifier where it is to be

—Places where it may interfere with the driver,

installed. Insert the supplied tapping

such as on the floor in front of the driver's

screws (4 × 18 mm) into the screw

seat.

• Make sure that wires are not caught in the sliding

holes. Push on the screws with a

mechanism of the seats, resulting in a short-cir-

screwdriver so they make marks

cuit.

where the installation holes are to be

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier.

located.

Protect all cables and important equipment such

as fuel lines, brake lines and electrical wiring

2. Drill 2.5 mm diameter holes at the

from damage.

point marked, and install the ampli-

• Install tapping screws in such a way that the screw

fier, either on the carpet or directly

tip does not touch any wire. This is important to

prevent wires from being cut by vibration of the

to the chassis.

car, which can result in fire.

• To prevent electric shock, do not install the ampli-

Tapping-screws

fier in places where it might come in contact with

(4 × 18 mm)

liquids.

• To ensure proper installation, use the supplied

parts in the manner specified. If any parts other

than the supplied ones are used, they may damage

internal parts of the amplifier, or they may

become loose causing the amplifier to shut down.

CAUTION:

To prevent malfunction and/or injury

• To ensure proper heat dissipation of the amplifier,

be sure of the following during installation.

Drill a 2.5 mm diameter hole

—Allow adequate space above the amplifier for

proper ventilation.

—Do not cover the amplifier with a floor mat or

carpet.

• Do not install the amplifier near a door where it

may get wet.

• Do not install the amplifier on unstable places

such as the spare tire board.

• The best location for installation differs with the

car model and installation location. Secure the

amplifier at a sufficiently rigid location.

• Make temporary connections first and check that

the amplifier and the system operate properly.

• After installing the amplifier, confirm that the

spare tire, jack and tools can be easily removed.

Specifications

Power source .............................................................................................................. 14.4 V DC (10.8 — 15.1 V allowable)

Grounding system ............................................................................................................................................ Negative type

Current consumption ........................................................................................................ 11.3 A (at continuous power, 4 Ω)

Average current drawn* ............................................................................................................ 3.8 A (4 Ω for two channels)

Fuse .................................................................................................................................................................................. 20 A

Dimensions ........................................................................................................................ 300 (W) × 61 (H) × 157 (D) mm

Weight ...................................................................................................................... 2.6 kg (Leads for wiring not included)

Maximum power output ...................................................................................................................... 80 W × 2 / 200 W × 1

Continuous power output .......................................................... 40 W × 2 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.08% THD)

100 W × 1 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.8% THD)

50 W × 2 (at 14.4 V, 2 Ω, 20 — 20,000 Hz, 0.8% THD)

Load impedance ............................................................................................................................ 4 Ω (2 — 8 Ω allowable)

Frequency response ............................................................................................................ 10 — 45,000 Hz (+0 dB, –1 dB)

Signal-to-noise ratio ...................................................................................................................... 100 dB (IEC-A network)

Distortion ............................................................................................................................................ 0.008% (10 W, 1 kHz)

Separation ........................................................................................................................................................ 55 dB (1 kHz)

Low pass filter ................................................................................................................................ Cut off frequency: 80 Hz

Maximum input level/impedance .................................................................................... RCA: 6.5 V/22 kΩ (0.4 — 6.5 V)

Note:

• Specifications and the design are subject to possible modification without notice

due to improvements.

*Average current drawn

• The average current drawn is nearly the maximum current drawn by this unit

when an audio signal is input. Use this value when working out total current

drawn by multiple power amplifiers.

Floor mat

or chassis

5.9 A (4 Ω for one channel)

(Bridge connection: 4 — 8 Ω allowable)

Cut off slope: –12 dB/oct

Speaker: 26 V/40 kΩ (1.6 — 26 V)