- ページ 3
CDプレーヤー Pioneer PD-S802-GのPDF サービスマニュアルをオンラインで閲覧またはダウンロードできます。Pioneer PD-S802-G 36 ページ。
ページを印刷する
— VARO!
AVATTAESSA
JA
SUOJALUKITUS
OHITETTAESSA
OLET
ALTTIINA
NAKYMATTOMALLE
LASERSATEILYLLE.
ALA KATSO SATEESEEN.
r-ADVERSEL:
USYNLIG
LASERSTRALING
VED
ABNING
NAR SIKKERHEDSAFBRYDERE
ER UDE AF
FUNKTION
UNOGA
UDSAETTELSE
FOR
STRALING.
VARNING!
OSYNLIG LASERSTRALNING NAR DENNA
DEL
AR
OPPNAD
OCH
SPARREN
AR URKOPPLAD. BETRAKTA EJ STRALEN.
LABEL
CHECK
CLASS 1
LASER PRODUCT
VRW-328
REAR VIEW
ADVARSEL
USYNLIG LASERSTRALING VED ABNING NAR SIKKERHED SAF-
BRYDERE ER UDE AF FUNKTION,
UNOGA UDSATTELSE FOR STRALING.
VORSICHT!
UNSICHTRARE LASER-STRAHLUNG TAITT AUS, WENN DECKEL
(ODER KLAPPE) GEGFENET IST! NICHT DEM STRAHL AUSSE TZEN!
VRW1094
HEM type
(FOR EUROPEAN
MODEL ONLY)
HB and HEM types
LASERS
Kuva 1
Lasersateilyn
varoitusmerkki
CAUTION
INVISIBLE LASER
RADIATION WHEN OPEN,
AVOID EXPOSURE
TO BEAM
HB type
WARNING!
DEVICE
INCLUDES
LASER
DIODE
WHICH
EMITS
INVISIBLE.
INFRARED
RADIATION
WHICH IS DANGEROUS TO EYES. THERE !S
A WARNING SIGN ACCORDING TO PICTURE
7 INSIDE THE DEVICE CLOSE TO THE LASER
DIODE.
IMPORTANT
THIS
PIONEER
APPARATUS
CONTAINS
LASER
OF
CLASS
1.
SERVICING OPERATION OF THE APPARATUS
SHOULD
BE
DONE
BY
A
SPECIALLY
INSTRUCTED
PERSON.
LASER DIODE CHARACTERISTICS
MAXIMUM
OUTPUT POWER:
5 mw
WAVELENGTH:
780-785 nm
LASER-
Picture 1
Warning sign for
laser radiation
PRW1018
. Laser Interlock Mechanism
. When the cover is opened with the servo mechanism
HEM type
VARO!
Avattaessa
ja suojalukitus
ohitetta-
essa
olet
alttiina
naikymaéttémdlle
lasersdteilylle.,
Ala katso
sdteeseen.
bis
VARNING!
pean
Osynlig
laserstrdlning
nér denna
del
&r Oppnad
och sparren
&r urkopplad,
Betrakta
ej strdlen.
PRWI233
Additional Laser Caution
The position of the switch (S601) for detecting loading
completion is detected by the system microprocessor, and
the design
prevents
laser diode
oscillation when
the
switch (S601) is not CLMP terminal side (when CLMP
signal is OFF, that is, high level). -
Thus, the interlock will no longer function if the switch
(S601) is deliberately set to CLMP terminal side (if CLMP
signal is low level).
In the test mode
+, the interlock mechanism
will not
function.
Laser diode oscillation will continue, if pin 1 of M51593FP
( 1C101
) on the preamplifier board loaded on pickup
assembly are connected to GND, or pin 19:is connected to
low level ( ON ), or else the terminals of Q101 are shorted
to each other ( fault condition ).
block removed to be turned over, close viewing of the
objective lens with the naked eye will cause exposure to a
Class 1 laser beam.
* : Refer to page 32.