- ページ 23

ウォーターヒーター Ariston FAST EVO X ONTのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Ariston FAST EVO X ONT 41 ページ。
Ariston FAST EVO X ONT にも：ユーザーマニュアル (42 ページ), 取扱説明書 (12 ページ)

ページを印刷する

postavljanje

Spajanje plina

Uređaj je dizajniran za korištenje plinova koji pripadaju

kategorijama kako je prikazano u donjoj tablici:

ZEMLJA

MODEL

FAST EVO X ONT 11 EU

FAST EVO X ONT 14 EU

Osigurajte, sukladno naljepnicama na uređaju i

podacima na pločici uređaja, da je uređaj u previđenoj

zemlji, te da kategorija plina za koju je uređaj dizajniran

odgovara dostupnim kategorijama u zemlji primjene.

Cijevi za opskrbu plinom moraju se izraditi i mjeriti u

skladu s posebnim zakonskim zahtjevima i u skladu s

maksimalnom snagom uređaja. Također, provjerite je li

ventil za zatvaranje pravilne veličine i je li pravilno

spojen.

Prije izvođenja instalacije preporučuje se temeljito

čišćenje cijevi za plin radi uklanjanja ostataka koji bi

mogli spriječiti pravilan rad uređaja.

Provjerite odgovara li isporučeni plin tipu plina za koji je

napravljen uređaj (pogledajte podatkovnu pločicu koja se

nalazi na samom uređaju).

Također je važno provjeriti je li pritisak plina (metana ili

LPG) koji koristite za napajanje uređaja prikladan, jer ako

je nedostatan, snaga generatora može biti smanjena, što

uzrokuje neugodnosti korisniku.

Spajanje vode

Ilustracija prikazuje priključke za vodu i plin uređaja.

Provjerite da maksimalni tlak vode ne prelazi 10 bara;

Ako da, potrebno je instalirati ventil za smanjenje tlaka.

Osigurajte da minimalni pritisak ne pada ispod 0,2

bara.

A. Izlaz tople vode 1/2"

B. Ulaz plina 1/2"

C. Ulaz hladne vode 1/2"

G. Filtar ulaza hladne vode

KATEGORIJA

II2H3+

Prikaz hidrauličnih spojeva

installation

Gas connection

The appliance was designed to use gases belonging to

the categories as shown in the following table.

COUNTRY

MODEL

FAST EVO X ONT 11 EU

FAST EVO X ONT 14 EU

Make sure, using the labels on the packaging and the

data plate on the appliance itself, that the appliance is in

the correct country and that the gas category for which

the appliance was designed corresponds to one of the

categories available in the country where it will be used.

The gas supply piping must be created and measured

out in compliance with specific legal requirements and in

accordance with the maximum power of the appliance;

you should also make sure that the shut-off valve is the

right size and that it is connected correctly.

Before carrying out the installation, it is recommended

that the fuel pipes are cleaned thoroughly in order to

remove any residues which could prevent the appliance

from operating correctly.

Check that the supplied gas corresponds to the type of

gas for which the appliance was designed (see the data

plate located on the appliance itself).

It is also important to check that the pressure of the gas

(methane or LPG) you will be using to feed the appliance

is suitable, because if it is insufficient the power of the

generator may be reduced, causing inconvenience for

the user.

Water connection

The illustration shows the connections for the water and

gas attachments of the appliance.

Check that the maximum water mains pressure does

not exceed 10 bar; if it does, a pressure reducing valve

must be installed.

Ensure that the minimum pressure is not lower

than 0,2 bar.

View of the hydraulic Connections