- ページ 12

ボイラー Ariston INTESA TP30のPDF ユーザーマニュアル、設置およびサービス手順書をオンラインで閲覧またはダウンロードできます。Ariston INTESA TP30 50 ページ。

ページを印刷する

Installation

6.9

Flue Connections

LUE

YSTEM

The provision for satisfactory flue termination must be made in

accordance with BS 5440-1.

The appliance must be installed so that the flue terminal is exposed

to outside air.

The terminal must not discharge into another room or space such

as an outhouse or lean-to.

It is important that the position of the terminal allows a free pas-

sage of air across it at all times.

The terminal should be located with due regard for the damage

or discolouration that might occur on buildings in the vicinity and

consideration must be given to adjacent boundaries.

In cold or humid weather water vapour may condense on leaving the

flue terminal. The effect of such "pluming" must be considered.

If the terminal is less than 2 metres above a balcony, above

ground or above a flat roof to which people have access, then a

suitable terminal guard must be fitted. When ordering a terminal

guard, quote the appliance model number.

A suitable terminal guard is available from:

TOWER FLUE COMPONENTS

Morley Road

Tonbridge

Kent TN9 1RA

The minimum acceptable spacing from the terminal to obstruc-

tions and ventilation openings are specified in F

. 6.7

ERMINAL

OSITION

A -

Directly below an openable window

or other opening300

B -

Below gutters, solid pipes or drain pipes

C -

Below eaves

D -

Below balconies or car-port roof

E -

From vertical drain pipes and soil pipes

F -

From internal or external corners

G -

Above ground or balcony level

H -

From a surface facing a terminal

I -

From a terminal facing a terminal

J -

From an opening in the car port

(e.g. door, window) into dwelling

K -

Vertically from a terminal in the same wall

L -

Horizontally from a terminal in the same wall

M -

Horizontally from an opening window

N -

Fixed by vertical flue terminal

: T

OTE

HE FLUE MUST NOT TERMINATE IN A PLACE LIKELY TO CAUSE

NUISANCE

Supplied By www.heating spares.co Tel. 0161 620 6677

IMPORTANT!

For all flue systems, a restrictor may need to be insert-

ed into the exhaust manifold, the size of the restrictor

and details of fitting requirements are shown in Table

6.1 (Page 18).

Ø 60/100 mm

. 6.7.

. 6.8

Fitting the Coaxial Flue (Horizontal)

(For Telscopic Instructions see page 13 and for Vertical Flue and

Twin Pipe Instructions see page 14)

ONTENTS

ILICONE

FU010ARev1

LBOW

ALL

LUMINIUM

LUE

CREWS

200

EALS

200

150

Once the boiler has been positioned on the wall, insert the elbow

300

into the socket (F

300

600

It is possible to rotate the elbow 360

1200

Using the flue clamps, seals and screws supplied (F

1200

secure the elbow to the boiler.

1500

300

The 1 metre horizontal flue kit (705958) supplied is suitable for an

300

exact X dimension of 823mm, and the 750mm horizontal flue kit

(705785) is suitable for an exact X dimension of 573mm.

Measure the distance from the face of the external wall to the

O-R

(60mm)

ING

(90

)

& E

EALS

NTERNAL

XTERNAL

LUE

IPE INCLUDING

ERMINAL

LAMPS

6.8) and rotate to the required position.

FU003A

)

- 60/100)

METRE

NOTE

on its vertical axis.

6.8)