- ページ 10
洗濯機 Whirlpool 3LCHW9100WQ0のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Whirlpool 3LCHW9100WQ0 48 ページ。 Semi-pro front-load washer
ページを印刷する
CONTROLSET.UPINSTRUCTIONS
WHITES
BRIGHTS
Semi-Pro
1. Door must be closed before cycle selection is made.
2. Press fabric setting key pad for the wash cycle desired. After
the cycle is started, the time will display and count down.
Scrolling
'out of order' showing
in display, followed
by a
failure code
This condition indicates the washer is inoperative.
"0 Minutes" showing in display
This condition indicates the washer cannot be operated. If a door
switch fails, it must be replaced before normal operation can be
restored.
Cold Start (initial first use)
Washer is programmed
at the factory as follows:
•
9-minute wash period
•
3 rinses (extra rinse not enabled)
Warm Start (after power failure)
A few seconds after power is restored, if a cycle was in progress
at the time of the power failure, "RESELECT CYCLE" will flash in
the display, indicating the need for a key press to restart washer.
IMPORTANT:
Read all instructions
before operating.
Set-up procedures can be entered by using the Service Access
Code (see service Access Code section).
IMPORTANT:
Unplug washer or disconnect
power before
opening the console. To access connector AA1 :
--*
Unplug washer or disconnect
power.
--*
Open console, disconnect
plug on AA1, close console.
--*
Plug in washer or reconnect power.
The washer is now in the set-up mode. The lower fabric setting
key pads and the digital display are used to set up the controls.
The display can contain 4 numbers and/or letters and a decimal
point. These are used to indicate the set-up codes and related
code values available for use in programming
the washer.
How to use the key pads to program
controls
1. The PERM PRESS key pad is used to adjust the
values associated with set-up codes. Pressing this key pad
will change the value by increments. Rapid adjustment
is possible by holding the key pad down.
2. The WOOLENS key pad advances you through the set-up
codes. Pressing this key pad will advance you to the next
available set-up code. Holding the key pad down will
automatically
advance through the set-up codes at a rate
of 1 per second.
3. The DELICATES/KNITS key pad is used to select or deselect
options.
Start Operating
Set-up
Before proceeding,
it is worth noting that, despite all of the
options available, an owner can simply choose to un-crate a new
semi-pro washer, hook it up, plug it in, and have a washer that
operates. Washers are preset at the factory for a 9-minute wash
period and 3 rinses (no extra rinse).
•
The WOOLENS key pad will advance you from code to code.
•
The PERM PRESS key pad will change the code value.
•
The DELICATES/KNITS key pad will select or deselect
options.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two or
three right-hand characters.
CODE
EXPLANATION
7 9
WASH LENGTH
7 9
This is the number of minutes for WASH. Washer
comes from the factory preset with 9 minutes.
Choose from 9-17 minutes by pressing the PERM
PRESS key pad.
-_
Press the WOOLENS key pad once to advance
to next code.
8 00
ADDITIONAL
RINSE OPTION
This option is either SELECTED "ON" or
NOT SELECTED "OFR"
8 00
Not Selected "OFR"
8 Ar
Selected "ON." Cannot be combined with the
Super Cycle rinse option.
Press the DELICATES/KNITS key pad once for this
selection.
-_
Press the WOOLENS key pad once to advance
to next code.
900
9 0C
9 00
CYCLE COUNTER
OPTION
This option is either SELECTED "ON" or
NOT SELECTED "OFR"
Not Selected "OFR"
Selected "ON" and not able to be deselected.
Press the DELICATES/KNITS key pad
3 consecutive
times to select "ON." Once selected
"ON" it cannot be deselected.
-_
Press the WOOLENS key pad once to advance
to next code.
10