- ページ 4

洗濯機 Whirlpool 3XLA87W72AN0のPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。Whirlpool 3XLA87W72AN0 5 ページ。 Whirlpool automatic washer top and cabinet parts
Whirlpool 3XLA87W72AN0 にも：パーツリスト (21 ページ)

ページを印刷する

IMPORTANT:

THIS PROCEDURE MUST

BE FOLLOWED

TO ASSURE PROPER

Open small

clamp and

INSTALLATION.

slide over "hook"

end of drain hose

to secure the

rigid and corrugated

sections together.

Floor Damage

Slide washer

onto

cardboard

hardboard

before

moving

across

floor.

Failure

to do so may cause

damage

to floor

covering.

:;:>,

::::::::.,,,

:::::::::::::::>,

::::::::::::::::::

:.:.::::::::;y

'.::.:.:.:.:.:.:.

. . . . . . . . .

. . . . . . . . . . . .

. . .

If drain hose does

not fit into standpipe

or is being placed over

the edge of a laundry

tub, open other hose

clamp with pliers and

place clamp over rigid

end of drain hose.

Insert end of hose

extension into rigid

end of drain hose up to stops

on the sides of hose extension.

Secure with clamp.

Move washer close to final

position. Put "hook"

end of drain

hose into laundry tub or standpipe.

Check for proper length of drain hose.

DO NOT FORCE EXCESS LENGTH OF

DRAIN HOSE DOWN THE STANDPIPE

THIS COULD CAUSE SIPHONING.

Inlets

are plastic.

DO NOT STRIP OR

CROSSTHREAD.

To prevent the drain h:sz from

coming off or leaking, it must be

iinstalled per the following

instructions.

Wet the inside end of the drain hose

with tap water. DO NOT USE ANY

OTHER LUBRICANT.

Squeeze ears of one hose clamp with

pliers to open and place clamp over the

end of the drain hose.

Open clamp and push end of drain hose

onto drain connector

until hose contacts

ribbed stop.

Place clamp over area marked "clamp".

Release clamp.

Attach bottom hose (inlet marked

"H") to hot water faucet. Attach

top hose (inlet marked "C") to cold watt

faucet. Adapters may be necessary to

connect the hoses to the faucets.

Tighten couplings to faucets. DO NOT

OVERTIGHTEN;

this could cause

damage to coupler.

Run water through

both faucets

into a bucket to get rid of

particles in the water lines that might

clog hoses. Mark the hot water faucet.

Leveling

washer:

II I

I-

Ill

i 10

Stack two corner posts on top

of each other. Tilt washer

.,:: .P..

..j::::

..:::::::::

I ..~;~~::~~~

:::::::.

. ..-.....-

. . . . . . . . . . ..-.

,.;:;:j:;:j::.'

,.::j:j:j::.'

.-.-

..;:-.

.:.

Tilt washer forward,

raising

back legs 2.54cm (1 inch) off

of floor to adjust rear self-leveling

legs.

Gently lower washer to floor. Check

levelness of the washer by placing a

carpenter's level on top of the washer,

first side to side; then front to back.

g backwards and insert corner posts 7.6 cm

j (3 inches) from one side of washer as

shown. Repeat with other corner posts

on other side of washer.

Insert legs into correct holes at each front

corner of washer until nuts touch washer.

NOT tighten nuts until Step 15.

Screw nut down on

legs to within 1.3cm

(l/2

inch) of base.

Tilt washer backward and

0 remove corner posts. Gently

lower washer to floor.

Floor Damage

Slide washer

onto

cardboard

hardboard

before

moving

across

floor.

Failure

to do so may cause

damage

to floor

covering.

If washer is not level, adjust the

front legs up or down. Repeat Step 14.

When

washer

is level,

use wrench

to turn

nuts on front

legs up

tightly

against

washer

base. If nuts

are not tight

against

washer

base,

the washer

may vibrate.

Move washer

to its final

location.

Remove

cardboard

or hardboard

from

under

washer.

bodies (not the handles or stems) as

shown in Figure C. Push plug into the

nearest hole in the shipping strap.

Securing

drain hose:

Property

Damage

Secure the drain

hose to

laundry

tub or standpipe

with

shipping

strap

removed

from

the back of the washer.

Failure

to properly

secure

drain

hose could

result

in water

damage.

If a longer drain hose is needed, drain

hose extension kit (Part No. 285702) is

available from authorized

parts

distributors.

If drain hose must be

shortened,

use hose kit (Part No.

285442).

Note:

If washer

is moved

to adjust

drain

hose, the washer

must

leveled

again.

Repeat

Steps 14-15.

place cardboard

under

the washer

and carefully

move washer

avoid

damaging

floor

covering.

Put "hook"

end of

drain hose in laundry

tub or standpipe.

Tightly wrap the

shipping strap around the drain hose and

laundry tub or standpipe

or inlet hose as

shown in Figures A-B. Push plug into the

nearest hole in the shipping strap.

II \\ v

13. w

If the water inlet

After strap has been removed from

faucets and drain

washer (Step l), measure and mark a

standing pipe are

point approximately

38.1 cm (15 inches)

recessed, put

from the plug end of the shipping strap.

"hook"

end of

Cut the shipping strap at this point.

drain hose in tub

or standpipe.

Check that

hose is not twisted

kinked

and is securely

in place.

Tightly wrap the

shipping strap

around the drain

hose and faucet

Panel C