- ページ 11
洗濯機 Whirlpool 3XLSQ7533のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool 3XLSQ7533 40 ページ。 Two speed automatic washer
Whirlpool 3XLSQ7533 にも： 取扱説明書 (35 ページ), 取扱説明書 (13 ページ), 取付説明書 (11 ページ)
ページを印刷する
Install and store your washer where it will not freeze. Because
some water may stay in the hoses, freezing can damage your
washer. If storing or moving your washer during freezing weather,
winterize it.
Non-use or vacation care
Operate your washer only when you are at home. If you will be on
vacation or not using your washer for an extended period of time,
you should:
Unplug washer or disconnect power.
Turn off the water supply to the washer. This helps avoid
accidental flooding (due to a water pressure surge) while you
are away.
To winterize washer
1. Shut off both water faucets.
2. Disconnect and drain water inlet hoses.
3. Put 1 qt (1 L) of R.V.-type antifreeze in the basket.
4. Run washer on a drain and spin setting (see "Drain and Spin")
for about 30 seconds to mix the antifreeze and water.
5. Unplug washer or disconnect power.
First try the solutions suggested here and possibly avoid the cost of a service call...
Washer won't fill, rinse or agitate; washer stops
WARNING
Electrical Shock Hazard
Plug into a grounded (earthed) outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Is the power cord plugged into an earthed 3 prong outlet?
Plug power cord into an earthed 3 prong outlet.
Are you using an extension cord? Do not use an extension
cord.
Vacation, Storage and Moving Care
To use washer again
1. Flush water pipes and hoses. Reconnect water inlet hoses.
2. Plug in washer or reconnect power.
3. Run the washer through a complete cycle with 1 cup
TROUBLESHOOTING
Turn on both water faucets.
WARNING
Electrical Shock Hazard
Plug into a grounded (earthed) outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
(250 mL) of detergent to clean out antifreeze.
Is the indicator on the Cycle Control knob properly lined
up with a cycle? Turn the Cycle Control knob to the right
slightly and pull to start.
Are the water inlet valve screens clogged? Turn off the
water and remove inlet hoses from the washer. Remove any
accumulated film or particles. Reinstall hoses, turn on water
and check for leaks.
Are both the hot and cold water faucets turned on? Turn
on the water.
Is the water inlet hose kinked? Straighten the hoses.
Does the water level seem too low, or does the washer
appear to not fill completely? The top of the agitator is
much higher than the highest water level. This creates a
perception that the washer is not filling completely. This is
normal.
Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
Is the washer in a normal pause in the Synthetics/
Permanent Press (or Hand Washables) cycle?
The washer pauses for about 2 minutes in the Synthetics/
Permanent Press cycle. Allow the cycle to continue.
The Hand Washables cycle (on some models) features
periods of agitation and soak.
Is the washer overloaded? Wash smaller loads.
Is the lid open? The lid must be closed during operation.
Washer will not agitate or spin with the lid open.
11