- ページ 4
洗濯機 Whirlpool 8182042のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool 8182042 44 ページ。 Front-loading automatic washer
ページを印刷するINSTALLATION
REQUIREMENTS
Tools and Parts
Assemble the necessary tools and supplies before beginning the
washer installation. The parts supplied are in the washer drum.
Tools needed for connecting the water inlet hoses
Pliers (that open to 1
Flashlight (optional)
Tools needed for installation
Open end wrench 17 mm and 13 mm
Level
Wood block (2" x 4")
Ruler or measuring tape
Parts supplied:
Beaded strap
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free
number on the cover or in the "Assistance or Service" section.
If You Have
You Will Need to Buy
Laundry tub or
Sump pump system (if not already
standpipe taller
available)
than 96 in. (2.4 m)
Overhead sewer
Standard 20 gal. (76 L), 30 in. (76.2 cm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)
Floor drain
Siphon break, Part Number 285834;
additional drain hose Part Number
8318155; and connector kit, Part
Number 285835
Drain hose too
Drain hose extension kit, Part Number
short
285863
Water faucets
2 longer water fill hoses:
beyond reach of
6 ft (1.8 m) Part Number 76314,
fill hoses
10 ft (3.0 m) Part Number 350008
4
in. [39.5 mm])
Transport bolt hole plug (4)
Options
Pedestal
Are you placing the washer on a pedestal? You may purchase a
pedestal separately for this washer. This pedestal will add about
13 in. (33 cm) to the height of your unit for a total height of
approximately 51 in. (130 cm).
Optional pedestal
To order, call the dealer from whom you purchased your washer
or refer to the "Assistance or Service" section of this manual. Ask
for Part Number LAB2700MQ (White), LAB2700MT (Biscuit) or
LAB2700ML (Pewter).
Stack Kit
Are you planning to stack your DUET
so you will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your dryer or
refer to the "Assistance or Service" section of this manual. Ask
for Part Number 8541503.
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer "walk."
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. (See "Drain
System.")
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need
A water heater set to deliver 120°F (49°C) water to the
washer.
A grounded electrical outlet located within 5 ft (1.5 m) of
where the power cord is attached to the back of the washer.
(See "Electrical Requirements.")
Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of
20-100 psi (137.9-689.6 kPa).
A level floor with a maximum slope of 1 in. (2.5 cm) under
entire washer. Installing the washer on carpeting is not
recommended.
A sturdy and solid floor to support the washer with a total
weight (water and load) of 400 lbs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage in
low temperatures.
®
washer and dryer? To do