- ページ 2
洗濯機 Whirlpool AWG 910 EのPDF プログラム表をオンラインで閲覧またはダウンロードできます。Whirlpool AWG 910 E 2 ページ。
ページを印刷する
30120130GB.fm Page 2 Wednesday, August 8, 2007 10:16 AM
CONSUMPTION DATA
Programme
White Cotton / Antibacterial
Cotton
Cotton with "Eco"***
Cotton
Synthetics
Synthetics
Daily load
Quick wash
Delicates
Wool
Handwash
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. In domestic use, consumption data
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The time indicated on the display (if present) can deviate from the values in the table, because it takes into account the household
conditions applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference programme for energy label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as
described in the chapter "Detergent and Additives"
in the Instructions for Use.
1. Turn the programme selector to the desired
programme.
2. The indicator of the predefined spin speed
lights up; in case you want to set another spin
speed, press the "Variable spin" button
SELECT ANY DESIRED OPTION
Press the button(s) of any required option(s) - the
respective indicator lights up.
When the combination of programme and
additional option(s) is not possible,
the indicators switch off automatically. Unsuitable
combinations of options are deselected automatically.
"Prewash" button
• Only for heavily soiled loads (e.g. sand, granular dirt).
Increases the cycle time by approx. 15 minutes.
• Do not use liquid detergent for the main wash
when activating the prewash option.
"Easy Ironing" button
• Can be used together with "Cotton",
"Synthetic" and "Daily load" programmes to
make ironing easier.
• Increases the water quantity and the clothes are
spun very gently.
Downloaded From WashingMachine-Manual.com Manuals
Black process 45.0° 150.0 LPI
Temperature
Load
Water
Energy
Approx. programme duration
(°C)
(kg)
(l)
(kWh)
(hours : minutes)*
90
5.0
52**
1.70
75
5.0
52
1.33
60
5.0
49
0.95
40
5.0
62
0.51
60
2.5
46**
0.80
40
2.5
46
0.46
40
3.5
52
0.30
35
2.5
30
0.40
30
2.5
54
0.24
40
1.0
56
0.44
30
2.0
65
0.24
"Intensive rinse" button
• More water is added and the rinse cycle is
prolonged.
• This option is particularly suitable for areas with
very soft water, washing baby linen, and helps
people with allergies.
"Rinse hold" button
• The laundry remains in the last rinse water
without the final spin cycle, to avoid creasing and
prevent colours from changing.
.
• This option is particularly recommended for the
"Synthetics", "Daily load" or "Delicates" programmes.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
• If you select "Rinse hold", do not leave the
laundry to soak for too long.
Note: The programme stops to "Rinse hold" at
the time the "Rinse Hold" light in the programme
sequence indicator is on. The indicator next to
the "Start"
button flashes.
To terminate the "Rinse hold" option
• Press the "Start"
button; the programme
will terminate automatically with the final spin
cycle for the preset wash programme.
"Variable spin" button
• Every programme has a predefined maximum
spin speed.
• Press the button to set another spin speed.
• If spin speed "0" is selected, the final spin is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
START DELAY
The "Start Delay"
option allows you to
programme machine activation at a later stage, for
example at night when electricity is cheaper. Do not
2:10
2:05
use liquid detergent when activating the "Start delay".
2:15
• Select the programme and options.
2:00
• Press the "Start Delay" button to select
1:40
programme start a delay time of 1 to 12 hours;
1:35
1:25
• Press the "Start" button
0:40
The indicator next to the "Start Delay" button
0:45
lights up, whereas the selection indicator flashes
0:54
to signal the countdown of the remaining time.
0:57
• At the end of the delay time the machine starts
the set programme. The LED indicating the
wash stage in progress lights up.
• After pressing the "Start"
hours preselected can be reduced by pressing
and holding the "Start Delay" button.
To cancel the "Start Delay":
Press the "Start Delay" button until all the indicator
lights are off. The selected programme will then start.
PROGRAMME START
Open the tap and press the "Start"
indicator next to the "Start"
The programme sequence indicator shows the
current programme stage, running from left to right
through Prewash, Wash, Rinse, Spin/Drain, End.
"DOOR OPEN" INDICATOR
At the end of a programme, the "End" indicator
lights up signalling that the door can be opened. As
long as a wash programme is running, the door
remains locked and must not be forced open. In
:
case you have an urgent need to open it during a
running programme, refer to "Cancel (Reset) a
running programme before the end".
RED INDICATORS
"Service" indicator
Lighting up of the "Service" indicator can be caused by
a fault in an electrical component. Refer to the
"Troubleshooting Guide" in the Instructions for Use; If
the fault persists, contact our After-Sales Service.
"Clean pump" indicator
The water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
("Removing the filter").
"Water tap closed" indicator
Machine water supply insufficient or lacking. Open
the water tap; Turn the programme selector to
"Off/0" and reset the programme. If the indicator
remains on, refer to the "Troubleshooting Guide" in
.
the Instructions for Use.
"Door lock" indicator
Lighting up of the indicator could be caused by the
door not being properly closed. Try closing it again.
Turn the programme selector to "Off/0" and reset the
programme. If the indicator remains on, refer to the
"Troubleshooting Guide" in the Instructions for Use.
, the number of
PROGRAMME END
• Lighting up of the lamp on the wash sequence
indicator means that the programme has ended
and the door is unlocked.
1. Turn the programme selector to the "Off/O"
position.
2. Close the water tap.
. The
3. Open the door and unload the machine.
button lights up.
4. Leave the door ajar to allow the drum to dry.
CHANGING PROGRAMME AND/OR
OPTIONS AFTER PROGRAMME START
1. Turn the programme selector to "Off/O".
2. Select the new programme, any options and
another spin speed if you want.
3. Press the "Start" button
programme resumes the wash programme from
where the previous one was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
• Reset by turning the programme selector to
"Off/0" and select the "Drain Spin" programme
to remove the water remaining in the bowl
before the door can be opened.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 20130
again. The new