- ページ 2
洗濯機 Whirlpool AWO/D 049のPDF パンフレットをオンラインで閲覧またはダウンロードできます。Whirlpool AWO/D 049 2 ページ。 5kg, 1000rpm fully integrated washing machine awo/d 049
Whirlpool AWO/D 049 にも： 取扱説明書 (14 ページ), インストレーション・マニュアル (14 ページ)
ページを印刷する
CONSUMPTION DATA
Temperature
Programme
(°C)
Cotton
95
Cotton***
60
Cotton
40
Synthetics
60
Synthetics
40
Quick wash
30
Delicate
30
Wool
40
Handwash
40
Handwash
30
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption
data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature,
the load and the type of wash.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains
the water out.
*** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as
described in your Instructions for Use. Close the
door and turn the programme selector to the
desired programme and temperature. The indication
lamp next to the "Start /Pause" button flashes.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
"Spin speed reduction 500 rpm" button
• Reduces the predetermined automatic maximum
spin speed to treat your laundry more gently.
Load
Water
Energy
Approx. Programme
Duration
(kg)
(l)
(kWh)
(hours : minutes)
5.0
49**
1.90
2:00
5.0
44
0.85
2:20
5.0
44
0.60
2:00
2.5
50**
0.70
1:30
2.5
45
0.55
1:15
3.0
40
0.40
0:30
1.5
50
0.50
0:45
1.0
55
0.60
0:45
1.0
45
0.60
0:40
1.0
45
0.50
0:40
"Rinse hold" button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes "Synthetics" and "Delicates".
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
Note: The programme stops to "Rinse hold" at
the time the "Rinse hold" light in the programme
sequence indicator is on. The indication lamp
next to the "Start/Pause" button flashes.
Terminate the "Rinse hold" option:
• Press the "Start/Pause" button; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the "Drain"
programme and press the "Start/Pause" button.
PROGRAMME START
Open the tap and press the "Start/Pause" button.
The indication lamp next to the "Start/Pause"
button lights up. The programme sequence indicator
shows the current programme phase, running from
left to right through Wash, Rinse, Spin/Drain.
When the programme phase is finished, the
corresponding indication goes out.
"DOOR OPEN" INDICATION
Before starting and after end of a programme, the
lamp lights to show that the door can be opened. As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to "Cancel
(Reset) a running programme before the end".
RED INDICATIONS
"Service"
Lighting up of the "Service" indication can be caused
by a fault in an electrical component. Refer to the
"Troubleshooting Guide" in your "Instructions for
Use"; if the fault persists, contact our After Sales
Service.
"Water tap closed"
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the "Troubleshooting Guide" in the
Instructions for Use.
"Clean pump"
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
("Removing the Filter").
PROGRAMME END
• All the lights of the programme sequence
indicator are off, and the "Door open"
indication lights up.
1. Turn the programme selector to the "Off/O"
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the "Start/Pause" button again. The new
programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
The "Reset" button cancels a programme before
the end.
• Press the "Reset" button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 10448