- ページ 2

洗濯機 Whirlpool AWO/D 41105のPDF プログラム表をオンラインで閲覧またはダウンロードできます。Whirlpool AWO/D 41105 2 ページ。

ページを印刷する
CONSUMPTION DATA
Temperature
Programme
(°C)
Cotton
95
Cotton***
60
Cotton
40
Synthetics
60
Synthetics
40
Delicates
30
Quick wash
30
Wool
40
Handwash
40
Lingerie
30
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption
data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature,
the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because it takes into account the household
conditions applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains
the water out.
*** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as
described in your Instructions for Use. Close the
door and turn the programme selector to the
desired programme and temperature. The indication
lamp next to the "Start /Pause" button
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
Load
Water
Energy
Approx. Programme
(kg)
(l)
(kWh)
(hours : minutes)*
5.0
49**
1.90
5.0
44
0.85
5.0
44
0.60
2.5
50**
0.70
2.5
45
0.55
1.5
50
0.50
3.0
40
0.40
1.0
55
0.60
1.0
45
0.60
1.0
45
0.50
"Intensive rinse" button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
"Spin speed reduction" button
flashes.
• Reduces the predetermined automatic maximum
spin speed to treat your laundry more gently.
PROGRAMME START
Open the tap and press the "Start/Pause"
button
. The indication lamp next to the "Start/
Duration
Pause" button
lights up. The programme
sequence indicator shows the current programme
2:00
phase, running from left to right through Wash, Rinse,
2:20
Spin/Drain.
2:00
When the programme phase is finished, the
1:30
corresponding indication goes out.
1:15
0:45
"DOOR OPEN" INDICATION
0:30
Before starting and after end of a programme, the
0:45
lamp lights to show that the door can be opened. As
0:40
long as a wash programme is running, the door
0:40
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to "Cancel
(Reset) a running programme before the end".
RED INDICATIONS
"Service"
Lighting up of the "Service" indication can be caused
by a fault in an electrical component. Refer to the
"Troubleshooting Guide" in your "Instructions for
Use"; if the fault persists, contact our After Sales
Service.
"Water tap closed"
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the "Troubleshooting Guide" in the
Instructions for Use.
"Clean pump"
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
("Removing the Filter").
PROGRAMME END
• All the lights of the programme sequence
indicator are off, and the "Door open"
indication
lights up.
1. Turn the programme selector to the "Off/O"
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button
to pause
the programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the "Start/Pause" button
again. The
new programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
The "Reset" button
cancels a programme
before the end.
• Press the "Reset" button
for at least 3
seconds. Any existing water is drained out
before the door can be opened.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 10283