- ページ 4

ホブ Ariston PK 760 RF GH AGのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Ariston PK 760 RF GH AG 42 ページ。 60-75cm

ページを印刷する

There is an adjustable L-shaped pipe fitting on the

appliance supply ramp and this is fitted with a seal in

order to prevent leaks. The seal must always be replaced

after rotating the pipe fitting (seal provided with

appliance). The gas supply pipe fitting is a threaded 1/2

gas cylindrical male attachment.

Connecting a flexible jointless stainless steel pipe to a

threaded attachment

The gas supply pipe fitting is a threaded 1/2 gas

cylindrical male attachment.

These pipes must be installed so that they are never

longer than 2000 mm when fully extended. Once

connection has been carried out, make sure that the

flexible metal pipe does not touch any moving parts and

is not compressed.

! Only use pipes and seals that comply with current

national regulations.

Checking the tightness of the connection

! When the installation process is complete, check the

pipe fittings for leaks using a soapy solution. Never use a

flame.

Adapting to different types of gas

To adapt the hob to a different type of gas other than

default type (indicated on the rating plate at the base of

the hob or on the packaging), the burner nozzles should

be replaced as follows:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a 7 mm socket spanner,

and replace them with nozzles for the new type of gas

(see table 1 "Burner and nozzle characteristics").

3. Reassemble the parts following the above procedure in

the reverse order.

4. Once this procedure is finished, replace the old rating

sticker with one indicating the new type of gas used.

Sticker are available from any of our Service Centres.

Replacing the nozzles on separate "double flame "

burners:

1. remove the grids and slide the burners from their

housings. The burner consists of 2 separate parts (see

figure);

2. unscrew the burers with a 7 mm wrench spanner. The

internal burner has a nozzle, the external burner has

two (of the same size). Replace the nozzle with models

suited to the new type of gas (see table 1).

3. replace all the components by repeating the steps in

reverse order.

• Adjusting the burners' primary air :

Does not require adjusting.

• Setting the burners to minimum:

1. Turn the tap to the low flame position.

2. Remove the knob and adjust the adjustment screw,

which is positioned in or next to the tap pin, until the

flame is small but steady.

! In the event of single-control DRDA (DCDR) burners,

adjustment can be performed by intervening on the 2

screws located near the tap pin (see picture).

3. Having adjusted the flame to the required low setting,

while the burner is alight, quickly change the position of

the knob from minimum to maximum and vice versa

several times, checking that the flame does not go out.

4. Some appliances have a safety device (thermocouple)

fitted. If the device fails to work when the burners are

set to the low flame setting, increase this low flame

setting using the adjusting screw.

5. Once the adjustment has been made, replace the seals

on the by-passes using sealing wax or a similar

substance.

6. In the event of discrete-adjustment knobs with

LED visualisation, turn the knob to the minimum

power setting them remove it and intervene on the

adjustment screw located near the tap pin.

7. Minimum setting adjustment of the DRDA (DCDR)

burner with discrete adjustment and LED

visualisation:

•

To adjust the outer ring, turn the knob anti-

clockwise to the minimum power position.

•

To adjust the minimum power setting of the

inner ring, turn the knob clockwise to the minimum

power position.

•

Remove the knob and intervene on the

adjustment screw located near the tap pin.

Total DRDA

(DCDR) burner

adjustment

Inner DRDA (DCDR)

burner adjustment