ページを印刷する
Start and Programmes
Programmes
Programme
What it does...
Automatic
Dries completely:
Drying
your clothes are ready to be
(average loads)
worn.
For average loads (from 1 to
3kg) of Cotton
or synthetics
Dries completely:
Automatic
Drying
your clothes are ready to be
(large loads)
worn.
For large loads (from 3 to 6kg) of
Cotton
Brief programme (approximately
Easy Iron
10 minutes) that softens fibres of
clothing that is ready for ironing.
Timed Drying
Dries wet clothes that will be
ironed, Acrylic fibres
up to 120 minutes
loads (less than 1kg).
If you prefer a timed programme
can be used for other fabrics on
High or Low heat as appropriate
(see Laundry).
Cool Tumble
Use to refresh fibres of clothing
(approximately 10 minutes).
Cool Tumble Phase
This is the programmes final phase. Approximately 10 minutes before the finish, the knob advances automatically to
the Cool Tumble Phase. Heating elements turn themselves off and clothing is cooled down, after this the Buzzer will
sound (if selected) and the clothing is ready to be taken out.
! Always allow the dryer to complete this phase so that the items are left at a temperature which ensures the items
will not be damaged.
Easy Iron Programme
'Easy Iron' is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which
fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The cycle
relaxes the fibres and makes them easier to iron and fold.
! 'Easy Iron' is not a drying programme and should not be used for wet articles of clothing.
For best results:
1. Do not load more than the maximum capacity.
These numbers refer to the dry weight:
Fabric
Cotton and Cotton mixtures
Synthetics
Denim
2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put
them away in the closet. Should this not be possible repeat the programme.
The 'Easy Iron' effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix,
and less well on acrylic fibres and on materials such as Tencel®.
How to set it...
1. Select High Heat by pressing
2. Position the PROGRAMMES knob
3. Press the Start button
, polycotton
.
1. Select High Heat by pressing the
HEAT button.
2. Position the PROGRAMMES knob
on
3. Press the Start button
.
Active light will turn on.
1. Select High Heat by pressing the
HEAT button.
2. Position the PROGRAMMES knob
on
3. Press the Start button
Active light will turn on.
1. Select required heat setting High
Heat or Low Heat by pressing the
, or small
HEAT button.
2. Position the PROGRAMMES knob
on the desired time.
3. Press the Start button
Active light will turn on.
1. Position the PROGRAMMES knob
2. Press the Start button
Maximum load
2.5kg
2kg
2kg
the HEAT button.
on
.
, the
Active light will turn on.
.
, the
.
, the
, the
on
.
, the
Active light will turn on.
Note:
! If you select Low Heat, this
programme will not dry your
clothes. For Acrylic fibres or
small loads select Timed
Drying.
This programme can also be
used for large loads if you
require a slightly drier result.
! If you select Low Heat, this
programme will not dry your
clothes. For Acrylic fibres or
small loads select Timed
Drying.
This programme can also be
used for average loads if you
prefer a damper result.
!
This is not a drying
programme (see below).
Consult suggested drying
times (see Laundry).
!
This is not a drying
programme (see below).
GB
7