- ページ 5

冷蔵庫 Whirlpool 3WSC19D4AY00のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Whirlpool 3WSC19D4AY00 24 ページ。

ページを印刷する

Remove the Doors

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Open both doors to 90°. Remove the base grille by removing

the two screws, then pulling out on the outside corners. See

Graphic 1.

NOTE: The doors must only be opened to 90°. If they are

opened all the way, the base grille will not come off.

3. Remove food, the ice storage bin, and any adjustable door or

utility bins from doors.

4. On dispenser models: Disconnect the water tubing, located

behind the base grille on the freezer door side. The dispenser

tubing runs through the door hinge, and must be

disconnected in order to remove the door.

Style 1: Press the colored outer ring against the face of

fitting and pull the water tubing free. See Graphic 2A.

NOTE: Keep the water tubing connector attached to the

tube that runs underneath the freezer. The door cannot be

removed if the connector is still attached to the tube that

runs through the door hinge.

Style 2: Firmly pull on the clasp to release the tube, then

pull the water tubing free. See Graphic 2B.

NOTE: Keep the clasp attached to the tube that runs

underneath the freezer.

5. Disconnect the wiring, located behind the base grille on the

freezer door side. See Graphic 3.

Remove the wiring clip using a ¹⁄₄" hex-head socket

wrench.

Disconnect the wiring plugs from the electrical housing.

6. Close both doors and keep them closed until you are ready to

lift them free from the cabinet.

7. Use a ³⁄₁₆" hex key to remove the top left hinge screws as

shown. See Graphic 4.

IMPORTANT: Do not remove either screw A.

8. Use an internal star drive or a ³⁄₈" hex-head socket wrench to

remove the bottom left hinge screws. See Graphic 7.

IMPORTANT: This requires two people — one to hold the

freezer door in place and another to remove the hinge screws.

NOTE: A leveler bracket is mounted behind the bottom hinge.

Make sure that the leveler bracket is replaced when

reinstalling the hinge.

WARNING

Excessive Weight Hazard

Use two or more people to lift the freezer door.

Failure to do so can result in back or other injury.

9. Remove the freezer door. See Graphic 5. The water tubing (on

dispenser models) and wiring remain attached to the freezer

door, along with the bottom left hinge.

IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket or piece of cardboard. This

will help avoid damaging the door, water tubing and wiring.

10. Use a ³⁄₁₆" hex key to remove the top right hinge screws as

shown. See Graphic 6.

IMPORTANT: Do not remove either screw A.

11. Lift the refrigerator door straight up off bottom hinge.

12. It may not be necessary to remove the bottom right hinge in

order to move the refrigerator through a doorway.

If necessary, use an internal star drive or a ³⁄₈" hex-head

socket wrench to remove the bottom right hinge. See

Graphic 7.

NOTE: A leveler bracket is mounted behind the bottom

hinge. If you remove the hinge, make sure that the leveler

bracket is replaced when reinstalling the hinge.

Replace the Doors and Hinges

1. Replace the bottom right hinge, if removed. Make sure that

the leveler bracket is assembled behind the hinge. Tighten

screws.

NOTE: When the screws are tightened properly, there should

not be any gaps between the refrigerator, leveler bracket and

hinge.

WARNING

Excessive Weight Hazard

Use two or more people to lift the freezer door.

Failure to do so can result in back or other injury.

2. Hold the freezer door in place in order to replace the bottom

left hinge. For easiest access, hold the door open 90°. Make

sure that the leveler bracket is assembled behind the hinge.

Tighten screws.

IMPORTANT: This requires two people — one to hold the

freezer door and another to reinstall the hinge screws.

NOTE: When the screws are tightened properly, there should

not be any gaps between the refrigerator, leveler bracket and

hinge.

3. Once the bottom left hinge has been replaced, close the

freezer door and make sure it is properly seated on the hinge.

Assistance may be needed.

NOTE: Provide additional support for the doors while the top

hinges are being replaced. Do not depend on the door magnets to

hold the doors in place while you are working.

4. Align and replace the top left hinge as shown. See Graphic 4.

Tighten screws.