![Ariston ASL800C 取扱説明書](/uploads/products/server2/680454/680454.jpg)
Start and Programmes
The Controls
PROGRAMMES knob
GB
! Warning, if after pressing the START/PAUSE button
, the programmes knob position has changed, the
new position will NOT change the programme selected.
To change a selected programme, press the
START/PAUSE button
indicate the programme is paused. Select the new
programme and any options required, the light will
then flash green. Press the START/PAUSE button
again and the new programme will start.
OPTION buttons / lights
These buttons are used to customise the selected
programme to your requirements. Not all options are
available for all programmes (see Start and
Programmes). If an option is not available and you
press the button, the buzzer will beep three times. If
the option is available there will be one beep and the
option light next to the button lights to confirm the
selection.
Progress (
Drying,
Delay (3hr, 6hr, 9hr) Lights
When the light next to the delay button is on, these lights
flash to indicate the delay time selected. During other
programmes they indicate the progress of the dryer,
each one comes on as the corresponding phase starts.
Time Delay
The start of some programmes (see Start and
Programmes) can be delayed for up to 9 hours in 3hr
steps. Ensure the water bottle is emptied before setting
a delayed start.
When a delayed start is in progress the light next to the
delay button will be on and the selected delay period
light will flash (after the start button has been pressed).
To set a delayed start, press the Time Delay button,
and the light next to the button will come on together
with the 3hr delay light. Pressing the button again will
advance the delay setting to 6hr, the 3hr light goes
out and the 6hr light is on. Each time you press the
button the delay setting advances 3 hours, as indicated
by the corresponding light. If the 9hr light is on,
pressing the button again will cancel the delay.
Holding in the On/Off button will also cancel.
Pre Creasecare
When a delayed start and this option have been
selected the clothes are tumbled occasionally during
the delayed period to help prevent creases developing.
High Heat
Available for Time Drying Programmes. Press this button
and a high heat setting is selected and the light next to
the button comes on. Timed programmes have a
default of low heat, if the light alongside the button is
on then pressing the button selects a low heat setting
and the light goes out.
8
,the light flashes Amber to
Cool Tumble,
) /
Post Creasecare
When selected, the clothes are occasionally tumbled
after the end of the drying and cool tumble cycles, to
help prevent creases developing should you not be
available to remove the load immediately the programme
is complete. The
light is on during this phase.
Empty Water Light / Container
(If you have plumbed your dryer to a drain this light
can be ignored, as there is no need to empty the water
container).
When this light is on (not flashing) it reminds you to
empty the water container.
If the water container fills during a programme, the
heater turns off and the dryer does a period of Cool
Tumble then the light flashes and the buzzer sounds.
You must empty the water container and restart the
dryer or the clothes will not dry. After re-starting the
dryer, the light will take a few seconds to go out.
To avoid this always empty the water container each
time you use the dryer (see Maintenance).
Door Opening
Opening the door (or pressing the START/PAUSE
button
) during a programme will stop the dryer
and have the following effects:
The START/PAUSE light flashes Amber.
During a delay phase the delay will continue to
count down. The start/pause button
pressed to resume the delay programme.
One of the delay lights will flash to show the
current delay setting.
The start/pause button
resume the programme. The progress lights will
change to show the current status and the
START/PAUSE light will stop flashing and turn green.
During the post creasecare phase of a drying
programme, the programme will finish. Pressing
the start/pause button
programme at the beginning.
Changing the programmes knob will select a new
programme and the START/PAUSE light will flash
green. You can use this to select the Cool Tumble
programme
to cool the clothes, if you find them
dry enough. Press the START/PAUSE button
begin a new programme.
Note
If you have a power cut, switch off the power or
remove the plug. When power is restored, press the
START/PAUSE button
and the programme will
resume.
must be
must be pressed to
will re-start a new
to