- ページ 10

冷蔵庫 Whirlpool WRT779RFYW10のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Whirlpool WRT779RFYW10 41 ページ。

ページを印刷する

models with notches:

Slide the indicator down into the notches, facing outward.

NOTE: The indicator will not easily slide into the notches

if the rear bubble has not been popped.

Close the air filter door, and check that the indicator is

visible through the rectangular hole in the door.

models without notches:

Store the indicator in a visible place you will easily

remember - either inside the refrigerator, or elsewhere in

your kitchen or home.

Style 2 - Air Filter Status on Electronic Control Display

The control panel displays the Air Filter status.

•

GOOD - The air filter LED does not light up.

REPLACE - The air filter LED lights up constantly when the

refrigerator door is open.

EXPIRED - The air filter LED lights up constantly and flashes

when the refrigerator door is open.

After replacing the air filter, press and hold FILTERS RESET for

3 seconds. The filter icons will turn off. See "Using the Control(s)."

NOTE: At any filter status, pressing and holding FILTERS RESET

for 3 seconds will reset the air filter status to good and the air filter

LED will turn off.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, or

when the status indicator air filter icon LED turns on and starts

flashing when the refrigerator door is opened.

To order a replacement air filter, contact us using the

assistance/service

information following the warranty.

1. Remove the old air filter by squeezing in on the side tabs.

2. Remove the old status indicator.

3. Install the new air filter and reset the status indicator using the

instructions

in the previous sections.

REFRIGERATOR USE

The temperature controls are located at the top front of the

refrigerator or freezer compartments.

Temperature Controls

For your convenience, the temperature controls are preset at the

factory. When you first install your refrigerator, make sure the

controls are still set to the recommended

setting as shown.

Style 1 - Electronic

Recommended

Setting "3 Snowflakes"

Filter

Status

Indicator

Temperature

Setting

Air

Water

Filter "_

Filter

"_'"_"'_4_'"_41_

"'"

COldest

IM PC RTANT:

The recommended

setting should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream is

firm.

Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended

setting will not cool

the compartments

any faster.

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

Adjusting Controls

If you need to adjust the temperature

in either the refrigerator or

freezer compartment,

use the settings listed in the chart below as

a guide.

Style 1 - Press the TEMP button to display the desired number of

snowflakes from (1 least cold to 4 coldest).

Style 2 - Move the dial to the desired number of snowflakes from

(1 least cold to 5 coldest).

NOTE: Except when starting the refrigerator, do not adjust either

control more than one setting at a time. Wait 24 hours between

adjustments for the temperature to stabilize.

CONDITION/REASON:

ADJUSTMENT:

REFRIGERATOR too warm

REFRIGERATOR Control

one setting higher

FREEZER too warm/too little ice

FREEZER Control one

setting higher

REFRIGERATOR too cold

REFRIGERATOR Control

one setting lower

FREEZER too cold

FREEZER Control one

setting lower

Cooling Off/On

Style 1 - Press and hold TEMP for 3 seconds to turn cooling off.

To turn cooling back on, press and hold TEMP again for

3 seconds.

Style 2 - Move the dial control to the word OFF. To turn cooling

back on, move the dial control to the desired temperature setting.

NOTE: Neither compartment will cool when the control is set to

OFR

Additional Features

Filters Reset (on some models)

The Filters Reset control allows you to restart the filter status

tracking feature each time you replace the air filter or water filter.

•

Press and hold FILTERS RESET for 3 seconds. The filter icons

will turn off. See "Install Air Filter" and "Water Filtration

System."

Style 2 - Dial

Recommended

Setting "3 Snowflakes"