- ページ 3
ドライヤー Whirlpool 27'のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Whirlpool 27' 11 ページ。 Microwave oven and thermal oven
Whirlpool 27' にも： ジョブエイド (36 ページ), 取付説明書 (11 ページ), 取付説明書 (48 ページ), 取付説明書 (22 ページ), 取付説明書 (27 ページ), 取付説明書 (32 ページ), 取付説明書 (12 ページ), インストレーション・インストラクション (5 ページ)
ページを印刷する
Electrical requirements
WARNING
Electrical Shock Hazard
Electrically ground oven.
Connect ground with 10-gauge-
minimum solid copper wire.
Failure to follow these instructions
could result in death, fire or electrical
shock.
If codes permit and a separate ground wire is
used, it is recommended that a qualified
electrician determine that the ground path
and wire gauge are in accordance with local
codes.
Installation Steps
Preparation
A
WARNING
Excessive Weight Hazard
Use two or more people to move
and install oven.
Failure to follow this instruction can
result in back or other injury.
Important: Use both hands to remove oven
doors.
Do Not use handle or any portion of the
front frame or trim for lifting.
Before moving oven across floor, check that
oven is on shipping base or slide oven onto
cardboard or hardboard.
Do Not remove shipping feet at the front
lower corners of oven.
Do Not
remove
shipping feet.
1.
Turn power supply off. Move oven
close to final position.
• Remove and discard shipping materials,
tape and protective film from the oven.
Do Not remove shipping base or shipping
feet at the front lower corners of oven.
The shipping feet will protect the lower
oven trim until oven is inserted into
cabinet.
• Remove and set aside racks and other
parts from inside oven.
Page 2
Do Not ground to a gas pipe.
Check with a qualified electrician if you are
not sure oven is properly grounded.
Do Not have a fuse in the neutral or ground
circuit.
Oven must be connected to the proper
electrical voltage and frequency as specified
on the model/serial rating plate. (The
model/serial rating plate is located on the
oven door or on the oven frame.)
CONNECT WITH COPPER WIRE ONLY.
Models rated from 7.3 to 9.6 kW at 240
volts (5.5 to 7.2 kW at 208 volts) require a
separate 40-ampere circuit. Models rated
at 7.2 kW and below at 240 volts (5.4 kW
and below at 208 volts) require a separate
30-ampere circuit.
A time-delay fuse or circuit breaker is
recommended.
Remove
A
side trim
pieces.
Grasp oven frame
C
to lift oven.
power
B
supply cable
shipping
A
foot
2.
Completely open lower oven door.
Insert small end of a door removal pin into
each door hinge. Grasp door handle from the
bottom and gently close door as far as it will
shut. Lift slightly and grasp bottom of door
with other hand. Pull door out at bottom to
remove. Set door aside on protected surface.
Connect directly to the fused disconnect
(or circuit breaker box) through flexible,
armored or non-metallic sheathed, copper
cable (with ground wire).
Flexible armored cable from appliance
should be connected directly to junction
box.
Fuse both sides of the line.
A U.L.-listed conduit connector must be
provided at the junction box.
Do Not cut the conduit.
Wire sizes and connections must conform
with the rating of the appliance and to the
requirements of the National Electrical Code,
ANSI/NFPA 70 — latest edition (*, See Page 1)
or Canadian Electrical Code, C22.1-1982 and
C22.2 No. 01982 (or latest edition) (**, See
Page 1) and all local codes and ordinances.
Remove
A
oven racks.
Insert small
end of pin
here.
3.
Remove trim screws attaching right
and left side trim to oven. Grasp the bottom
end of trim and pull away from oven. Slide
top end of trim downward to remove trim
from oven. Take care not to scratch other
surfaces with ends of trim. Set trim and
screws aside on protected surface.
Check oven and
D
microwave oven operation.
Use screws to attach
C
oven to cabinet.
Reattach side
C
trim pieces.
Remove
A
trim screws.
Remove
A
oven door.
Replace
C
oven door.
Remove trim screw.
Pull trim out.
Pull top of trim
down.