- ページ 10

ドライヤー Whirlpool 29 (73.)のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Whirlpool 29 (73.) 12 ページ。 29 in. (73.7 cm) electric dryer

ページを印刷する

1. Tools and Parts

Vent Length Chart

Number of

Type of vent

90º turns

or elbows

Rigid metal

Flexible metal

Rigid metal

Flexible metal

Rigid metal

Flexible metal

Rigid metal

Flexible metal

Rigid metal

Flexible metal

Install Vent System

1. (Optional) Put on safety glasses and gloves.

2. Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

3. Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4 in. (10.2 cm) clamp.

4. Run vent to dryer location. Use the straightest path possible.

See "Determine Vent Length." Avoid 90º turns. Use clamps to

seal all joints. Do not use duct tape, screws or other fastening

devices that extend into the interior of the vent to secure vent.

Install Leveling Legs

WARNING

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. To protect the floor, use a large, flat piece of cardboard from

the dryer carton. Place cardboard under the entire back edge

of the dryer. See illustration.

2. Firmly grasp the body of the dryer (not the top or console

panel).

Gently lay the dryer on the cardboard.

3. Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to

finish turning the legs until the diamond marking is no longer

visible.

Box or

Angled

Louvered

hoods

64 ft (20 m)

58 ft (17.7 m)

36 ft (11 m)

28 ft (8.5 m)

54 ft (16.5 m)

48 ft (14.6 m)

31 ft (9.4 m)

23 ft (7 m)

44 ft (13.4 m)

38 ft (11.6 m)

27 ft (8.2 m)

19 ft (5.8 m)

35 ft (10.7 m)

29 ft (8.8 m)

25 ft (7.6 m)

17 ft (5.2 m)

27 ft (8.2 m)

21 ft (6.4 m)

23 ft (7 m)

15 ft (4.6 m)

5. Place a carton corner post under each of the 2 dryer back

corners. Stand the dryer up. Slide the dryer on the corner

posts until it is close to its final location. Leave enough room

to connect the exhaust vent.

6. Once connection is made and dryer is in final location, remove

corner posts and cardboard.

Level Dryer

Check the levelness of the dryer. Check levelness first

side-to-side, then front-to-back.

If the dryer is not level, prop up the dryer using a wood block. Use

a wrench to adjust the legs up or down and check again for

levelness.

NOTE: It might be necessary to level the dryer again after it is

moved into its final position.

Connect Vent

1. Using a 4 in. (10.2 cm) clamp, connect vent to exhaust outlet

in dryer. If connecting to existing vent, make sure the vent is

clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Make sure the vent is secured to

exhaust hood with a 4 in. (10.2 cm) clamp.

2. Move dryer into final position. Do not crush or kink vent. Make

sure dryer is level.

3. (On gas models) Check to be sure there are no kinks in the

flexible gas line.

Reverse Door Swing (Optional)

You can change your door swing from a right-side opening to a

left-side opening, if desired.

Reversible Large Side-Swing Door

1. Place towel (1) on top of dryer to protect surface.

2. Open dryer door. Remove bottom screws from cabinet side of

hinges (3). Loosen (do not remove) top screws from cabinet

side of hinges.

3. Lift door until top screws in cabinet are in large part of hinge

slot. Pull door forward off screws. Set door on top of dryer.

Remove top screws from cabinet.

4. Use a small, flat-blade screwdriver to carefully remove 4 hinge

hole plugs (4) on left side of cabinet. Insert plugs in hinge

holes on right side of cabinet.