- ページ 19

ドライヤー Whirlpool 8578901のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool 8578901 44 ページ。 Duet sport electronic electric dryer

ページを印刷する

First try the solutions suggested here and possibly avoid the cost of a service call...

Dryer Operation

Dryer will not run

Has a household fuse blown, or has a circuit breaker

tripped?

There may be 2 fuses or circuit breakers for the dryer. Check

that both fuses are intact and tight, or that both circuit

breakers have not tripped. Replace the fuse or reset the

circuit breaker. If the problem continues, call an electrician.

Is the correct power supply available?

Electric dryers require 240-volt power supply. Check with a

qualified electrician.

Was a regular fuse used?

Use a time-delay fuse.

Is the dryer door firmly closed?

Was the Power button pressed?

Was the Start button firmly pressed?

Press and hold for 1 second.

No heat

Has a household fuse blown, or has a circuit breaker

tripped?

The drum may be turning, but you may not have heat. Electric

dryers use 2 fuses or circuit breakers. Replace the fuse or

reset the circuit breaker. If the problem continues, call an

electrician.

Unusual sounds

Has the dryer had a period of non-use?

If the dryer hasn't been used for a while, there may be a

thumping sound during the first few minutes of operation.

Is a coin, button, or paper clip caught between the drum

and front or rear of the dryer?

Check the front and rear edges of the drum for small objects.

Clean out pockets before laundering.

Are the four legs installed, and is the dryer level front to

back and side to side?

The dryer may vibrate if not properly installed. See

"Installation Instructions."

Is the clothing knotted or balled up?

When balled up, the load will bounce, causing the dryer to

vibrate. Separate the load items and restart the dryer.

Dryer displaying code message

"PF" (power failure), check the following:

Was the drying cycle interrupted by a power failure?

Press and hold START to restart the dryer.

"F-" Variable (F-01, F-22, F-23, F-26) service codes (the

display alternately flashes "F-" and then the error code

number):

Call for service.

TROUBLESHOOTING

Clothes are not drying satisfactorily, drying times are too

long, or load is too hot

Is the lint screen clogged with lint?

Lint screen should be cleaned before each load.

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

Is the exhaust vent or outside exhaust hood clogged with

lint, restricting air movement?

Run the dryer for 5-10 minutes. Hold your hand under the

outside exhaust hood to check air movement. If you do not

feel air movement, clean exhaust system of lint or replace

exhaust vent with heavy metal or flexible metal vent. See

"Venting Requirements."

Are fabric softener sheets blocking the grille?

Use only one fabric softener sheet, and use it only once.

Is the exhaust vent the correct length?

Check that the exhaust vent is not too long or has too many

turns. Long venting will increase drying times. See "Plan Vent

System."

Is the exhaust vent diameter the correct size?

Use 4" (10.2 cm) diameter vent material.

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

Is the dryer located in a room with temperature below

45ºF (7ºC)?

Proper operation of dryer cycles requires temperatures above

45ºF (7ºC).

Dryer Results

WARNING

Fire Hazard

WARNING

Explosion Hazard