- ページ 9

ドライヤー Whirlpool Cabrio WGD5700XWのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Whirlpool Cabrio WGD5700XW 48 ページ。 High-efficiency laundry with 6th sense technology
Whirlpool Cabrio WGD5700XW にも：取扱説明書 (28 ページ), 取扱説明書 (8 ページ), 仕様 (1 ページ)

ページを印刷する

Option 1 (Recommended Method)

Flexible stainless steel gas connector:

If local codes permit, use a new flexible stainless steel gas

■

connector (Design Certified by the American Gas Association

or CSA International) to connect your dryer to the rigid gas

supply line. Use an elbow and a 3/8" flare x 3/8" NPT adapter

fitting between the stainless steel gas connector and the

dryer gas pipe, as needed to prevent kinking.

Option 2 (Alternate Method)

Approved aluminum or copper tubing:

Lengths over 20 ft. (6.1 m) can use 3/8" approved tubing

■

(if codes and gas supplier permit).

If you are using Natural Gas, do not use copper tubing.

■

3/8" flare x 3/8" NPT adapter fitting between dryer pipe and

■

3/8" approved tubing.

Lengths over 20 ft. (6.1 m) should use larger tubing and a

■

different size adapter fitting.

If your dryer has been converted to use LP gas, 3/8" LP

■

compatible copper tubing can be used. If the total length

of the supply line is more than 20 ft. (6.1 m), use larger pipe.

NOTE: Pipe joint compounds that resist the action of LP

gas must be used. Do not use TEFLON

Dryer gas pipe

The gas pipe that comes out through the rear of your dryer

■

has a 3/8" male pipe thread.

29" Wide Model

A. 3/8" NPT dryer pipe

27" Wide Model

(159 mm)

A. 3/8" NPT dryer pipe

Burner input requirements

Elevations up to 10,000 ft. (3,048 m):

The design of this dryer is certified by CSA International for

■

use at altitudes up to 10,000 ft. (3,048 m), above sea level at

the B.T.U. rating indicated on the model/serial number plate.

Burner input adjustments are not required when the dryer is

operated up to this elevation.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

tape.

®†

1¼"

(32 mm)

9¼"

(235 mm)

(38 mm)

Elevations above 10,000 ft. (3,048 m):

When installed above 10,000 ft. (3,048 m) a 4% reduction

■

of the burner B.T.U. rating shown on the model/serial

number plate is required for each 1,000 ft. (305 m)

increase in elevation.

Gas supply pressure testing

The dryer must be disconnected from the gas supply piping

■

system during pressure testing at pressures greater than

1/2 psi.

Electrical Requirements

120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical

■

supply is required. A time-delay fuse or circuit breaker is

recommended. It is also recommended that a separate circuit

serving only this dryer be provided.

GROUNDING INSTRUCTIONS

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING:

Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a quali ed electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not t the outlet, have a proper outlet

installed by a quali ed electrician.

SAVE THESE INSTRUCTIONS