- ページ 4
ドライヤー Whirlpool GEW9868KQのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Whirlpool GEW9868KQ 7 ページ。 Installation instructions
ページを印刷する
I
Put on safety glasses and gloves.
Install
exhaust
hood.
Use caulking
compound
to seal --
exterior
wall opening
around
exhaust
hood.
Connect vent to exhaust hood with 4"
clamp. (Exhaust vent MUST fit inside hoodO
Run exhaust vent to dryer location.
Use the straightest path possible. (See Panel B.)
Use clamps to secure vent pieces, Tin snips may be
needed to cut vent to required length,
SLIDE DRYER
ONTO
HARDBOARD
BEFORE
MOVING
ACROSS
FLOOR TO PREVENT
FLOOR DAMAGE,
Excessive
Weight Hazard
Use two or more people to move and install dryer.
Faimure to do so can resumt in back or other injury.
Open dryer door and drying rack, if included.
Wipe drum with damp cloth to remove any dust.
Take two cardboard
corners from dryer carton and
_-_
place them on floor in back of
dryer. Firmly grasp body of dryer
and gently lay it on its back on the
cardboard corners,
1
Start to screw legs into holes by hand. Use
an adiustabie wrench or 1" hex-head socket wrench
to finish turning Iegs until you reach the ridge with
the diamond marking.
Stand dryer up on cardboard or hardboard.
This dwer
is manufactured
with
the cabinet-
ground
conductor
connected
to the
NEUTRAL
(center)
of the wiring
harness
at the terminal
block.
If local
codes
do NOT permit
this type
of
connection,
use "Four-wire
connection"
instructions.
GROUNDING
INSTRUCTIONS:
This appliance
must
be grounded.
In the event of malfunction
or
breakdown,
grounding
will reduce
the risk of
electric
shock
by providing
a path
of least
resistance
for electric
current.
If using a power
supply
cord,
the plug
must be
plugged
into
an appropriate
outlet
that is properly
installed
and grounded
in accordance
with
all local
codes and ordinances.
If using a direct
wire connection,
this appliance
must
be connected
to a grounded
metal,
permanent
wiring
system;
or an equipment°
ground
conductor
must
be run with
the circuit
conductors
and connected
to the equipment°
ground
terminal
or lead on the appliance.
WARNING
- Improper
connection
of the
equipment-grounding
conductor
can result
in a
risk of electric
shock.
Check with
a qualified
electrician
or serviceman
if you are in doubt
as to
whether
the appliance
is properly
grounded.
Do
not modify
the power
supply
cord
plug.
If it will
not fit the outlet,
have a proper
outlet
installed
by
a qualified
electrician.
Pewer supply cerd
Fire Hazard
Use a new UL approved
30 ampere power
supply cord.
Use a UL approved
strain relief.
Disconnect
power before making electrical
connections.
Connect
neutral wire (white or center wire}
to center terminal
(silver).
Ground wire (green or bare wire} must be
connected
to green ground connector.
Connect
remaining
2 supply wires to
remaining
2 terminals
(gold).
Securely tighten
all electrical
connections.
Failure to do so can result in death, fire, or
electrical
shock.
].
Disconnect
the power
supply,
hold-down
screw
2,
Remove
holddown
screw and terminal
terminal
block
cover,
block
cover
extemal
ground
conductor
screw
Direct wire
Fire Hazard
Use 10 gauge solid copper wire.
Use a UL approved
strain relief.
Disconnect
power before making electrical
connections.
Connect
neutral wire (white or center wire)
to center terminam (sHyer).
Ground wire (green or bare wire} must be
connected
to green ground connector.
Connect
remaining
2 supply wires to
remaining
2 terminals
(gold}.
Securely tighten
all electrical
connections.
Failure to do so can result in death, fire, or
electrical
shock.
strain
3,
Assemble
3/4"
relief
screws just enough
to hold
screws
the two
clamp
sections
together.
Install
power
supply
cord/cable
through
the strain
relief.
Complete
installation
following
instructions
for
your
type
of connection:
• Fourowire
(recommended
method)
Three-wire
(if four-wire
is not available)
Four-wire
power
supply
cord
at least four feet
long
must
have four,
NoA
0 copper
wires and
match
a four-wire
receptacle
of NEMA Type
14o30R.
The fourth
wire (ground
conductor)
must
be identified
with
a green
cover and the
neutral
conductor
by a white
cover.
14-30R
Four-wire
receptacme (required
for
mobime homes)
4,
Remove
center
terminal
block
screw.
5,
Remove
appliance
ground
wire (green
_
with
yellow
stripes)
from
external
ground
z
.
X
connector
screw.
Fasten under center,
O
Connect
ground
w_re
"
_
silver-colored
terminal
block
screw.
(green)
of power
supply
cord
to
_
/
external
ground
conductor
f-
....
"
screw. Tighten
screw.
external
9roun
8,
Connect
the other
_Mres to-
;
;
outer
terminal
block
screws.
Tighten
screws.
_
7,
Connect
neutral
9.
Tighten strain
relief screws.
1
I U.
insert tab of terminal
block
cover
into slot of the
dryer
rear panel
Secure
cover
with
hold-down
screw.
wire (white or center)
of power supply cord
under center screw of
the terminal block.
Tighten screw.
Panel C