- ページ 15

ドライヤー Whirlpool WGD9450WW - 27" Gas DryerのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Whirlpool WGD9450WW - 27" Gas Dryer 32 ページ。 Steam and non-steam electronic gas dryer
Whirlpool WGD9450WW - 27" Gas Dryer にも：仕様 (8 ページ), 取扱説明書 (28 ページ), 寸法 (1 ページ)

ページを印刷する

If you receive an L2 code, there may be a problem with your

home power supply keeping the dryer's heater from turning on.

See "Troubleshooting."

16. When the dryer has been running for 5 minutes, open the dryer

door and feel for heat. If you feel heat, cancel cycle and close the

door.

First try the solutions suggested here and possibly avoid the cost of a service call...

Dryer Operation

Dryer will not run

■

Has a household fuse blown, or has a circuit breaker

tripped?

There may be 2 household fuses or circuit breakers for the dryer.

Check that both fuses are intact and tight, or that both circuit

breakers have not tripped. Replace the fuse or reset the circuit

breaker. If the problem continues, call an electrician.

■

Is the correct power supply available?

Electric dryers require 240-volt power supply. Check with a

qualified electrician.

■

Was a regular fuse used?

Use a time-delay fuse.

No heat

■

Has a household fuse blown, or has a circuit breaker

tripped?

The drum may be turning, but you may not have heat. Electric

dryers use 2 household fuses or circuit breakers. Replace the

fuse or reset the circuit breaker. If the problem continues, call an

electrician.

Dryer displaying code message

■

"PF" (power failure), check the following:

Was the drying cycle interrupted by a power failure?

Press and hold START/PAUSE to restart the dryer.

■

"L2" Diagnostic Code (low or no line voltage condition):

The drum will turn, but there may be a problem with your home

power supply keeping the dryer's heater from turning on. The

dryer will continue to run when this diagnostic code is present.

Press any key to clear the code from the display and return to

the estimated time remaining.

Try the following:

Check to see if a household fuse has blown or circuit breaker

has tripped. Electric dryers use two household fuses or

breakers. Replace the fuse or reset the circuit breaker.

Confirm the power cord is properly installed. Refer to "Electrical

Connection" for details.

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, consult a qualified electrician.

NOTE: You may notice a odor when the dryer is first heated. This

odor is common when the heating element is first used. The odor

will go away.

TROUBLESHOOTING

■

If you do not feel heat, turn off the dryer and check the

following:

■

There may be 2 household fuses or circuit breakers for the

dryer. Check that both fuses are intact and tight, or that both

circuit breakers have not tripped. If there is still no heat,

contact a qualified technician.

"AF" (low airflow condition):

The dryer will continue to run when this diagnostic code is

present. Press any key to clear the code from the display and

return to the estimated time remaining.

Try the following:

■

Clean lint screen.

■

Check to see if the vent run from the dryer to the wall is

crushed or kinked.

■

Confirm the vent run from the dryer to the wall is free of lint

and debris.

■

Confirm the exterior vent exhaust hood is free of lint and

debris.

■

Confirm your vent system falls within the recommended run

length and number of elbows for the type of vent you are

using. Refer to "Plan Vent System" for details.

■

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, have your entire home venting run

cleaned.

"E" Variable (E1, E2, E3) service codes:

Call for service.