ドライヤー Whirlpool WGD9500TのPDF 寸法をオンラインで閲覧またはダウンロードできます。Whirlpool WGD9500T 1 ページ。 Duet steam electronic gas dryer
Whirlpool WGD9500T にも：寸法と設置について (3 ページ)

ページを印刷する

PRODUCT MODEL NUMBERS

WGD9500T

Gas supply: This dryer is equipped for use with

Natural gas. Dryer can be converted to L.P. gas.

When rigid pipe is used it should be 1/2" IPS.

When acceptable to the gas supplier and local

codes, 3/8" approved tubing may be used for

lengths under 20 ft. (6.1 m). For lengths over

20 ft. (6.1 m), larger tubing should be used.

Pipe-joint compounds resistant to the action of

L.P. gas must be used. An individual manual

shutoff valve must be installed within 6 ft. (1.8 m)

of the dryer in accordance with the National Fuel

Gas Code ANSI Z223.1.

Electrical: A 120-volt, 60 Hz, AC-only,

15 or 20 amp fused electrical supply is required.

A time-delay fuse or circuit breaker and a separate

circuit are recommended.

Exhaust venting: Exhaust your dryer to the

outside. Four inch (10.2 cm) diameter vent is

required. Rigid or flexible metal exhaust vent must

be used. Do Not use plastic or metal foil vent.

Exhaust hood must be at least 12" (30.5 cm) from

the ground or any object that may be in the path

of the exhaust.

Water: The dryer must be connected to the cold

water faucet using new inlet hoses. Do not use old

hoses. Do not over tighten. Damage to the

coupling can result.

EXHAUST VENTING

Recommended hood styles

Angled hood style is

(10.2 cm)

A. Louvered hood style

B. Box hood style

Number of

Type of

Box or

90° turns

vent

Louvered

or elbows

hoods

Rigid metal

64 ft (20 m)

Flexible metal

36 ft (11 m)

Rigid metal

54 ft (16.5 m)

Flexible metal

31 ft (9.4 m)

Rigid metal

44 ft (13.4 m)

Flexible metal

27 ft (8.2 m)

Rigid metal

35 ft (10.7 m)

Flexible metal

25 ft (7.6 m)

Rigid metal

27 ft (8.2 m)

Flexible metal

23 ft (7 m)

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add one

90° turn to the chart.

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Duet

Steam Electronic Gas Dryer

OVERALL DIMENSIONS

38"

(96.52 cm)

RECESSED AREA AND CLOSET INSTALLATION

For closet installation, with a door, the minimum ventilation openings in the top and

bottom of the door are required. Louvered doors with equivalent air ventilation openings

are acceptable.

1"*

(2.5 cm)

acceptable.

**For side or bottom venting, 2" (5.1 cm)

2-1/2"

(6.4 cm)

Recommended installation

Angled

spacing for cabinet installation

hoods

For cabinet installation, with a door,

the minimum ventilation openings

58 ft (17.7 m)

in the top of the cabinet are

28 ft (8.5 m)

required.

48 ft (14.6 m)

23 ft (7 m)

38 ft (11.6 m)

19 ft (5.8 m)

29 ft (8.8 m)

17 ft (5.2 m)

21 ft (6.4 m)

Select the route that will provide the straightest and most direct path outdoors. Plan the

15 ft (4.6 m)

installation to use the fewest number of elbows and turns. Use the fewest 90° turns possible.

Do not use vent runs longer than specified in vent length chart.

Determine the number of elbows you will need.

51-1/2"

(130.81 cm)

*31-1/2"

(82.65 cm)

27"

(68.6 cm)

Dryer only

14" max.*

48 in.

(35.6 cm)

(310 cm

)

18" min.*

(45.72 cm)

24 in.

(155 cm

)

31-1/2"

5"**

(80 cm)

(12.7 cm)

A. Side view - closet or confined area

B. Closet door with vents

*Required spacing

spacing is allowed.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Undercounter - Dryer only

(0 cm)

38" min.

(96.52 cm)

(2.5 cm)

*Required spacing

*Most installations require a minimum 5"

(12.7 cm) clearance behind the dryer for the

exhaust vent with elbow. See Installation

Instructions, "Venting Requirements."

Dryer on pedestal

3"*

(7.6 cm)

3"*

27"

(7.6 cm)

(2.5 cm)

(68.6 cm)

A. Recessed area

B. Side view - closet or confined area

*Required spacing

**For side or bottom venting, 2" (5.1 cm)

spacing is allowed.

7"* (17.8 cm)

31-1/2

5"**

(80 cm)

(12.7 cm)

*Required spacing

**For side or bottom venting, 2" (5.1 cm) spacing is allowed.

1"*

27"

1"*

(2.5 cm)

(68.6 cm)

14" max.*

(35.6 cm)

18" min.*

(45.72 cm)

31-1/2

5"**

1"*

(80 cm)

(12.7 cm)

(2.5 cm)

9"*

(22.9 cm)

27"

1"*

(68.6 cm)

(2.5 cm)

Ref. W10122320

09-12-07