- ページ 12

ドライヤー Whirlpool WGD9750WL1のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool WGD9750WL1 29 ページ。 Electronic dryer

ページを印刷する

•

Is the exhaust vent diameter the correct size?

Use 4" (102 mm) diameter vent material.

Explosion

Hazard

Keep flammable

materials

and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (460 ram) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

Is the dryer located in a room with temperature

below 45°F

(7°C)?

Proper operation of dryer cycles requires temperatures above

45°F (7°C).

Is the dryer located in a closet?

Closet doors must have ventilation openings at the top and

bottom of the door. The front of the dryer requires a minimum

of 1" (25 mm) of airspace, and, for most installations, the rear

of the dryer requires 5" (127 mm). See the Installation

Instructions.

Cycle time too short

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

•

Is the automatic cycle ending early?

The load may not be contacting the sensor strips. Level the

dryer.

Change the dryness level setting on Automatic

Cycles.

Increasing or decreasing the dryness level will change the

amount of drying time in a cycle.

Lint on load

•

Is the lint screen clogged?

Clean lint screen. Check for air movement.

Stains on load or drum

Was dryer fabric softener properly used?

Add dryer fabric softener sheets at the beginning of the cycle.

Fabric softener sheets added to a partially dried load can

stain your garments. Do not use fabric softener sheets with

steam cycles.

Drum stains are caused by dyes in clothing (usually blue

jeans). These will not transfer to other clothing.

Loads are wrinkled

Was the load removed from dryer at the end of the cycle?

Select Enhanced Touch Up Cycle to tumble the load with

water and heat. This cycle is best for smoothing out wrinkles

and reducing odors from loads consisting of wrinkle-free

cotton, cotton polyester blends, common knits, and synthetic

garments.

NOTE: Refer to garment care label instructions. Dry clean only

garments are not recommended.

Loads are still wrinkled following Steam Cycle?

Make sure water is connected to the dryer. Check that water

inlet hose is connected to both the faucet and dryer's water

inlet valve. Check that the water supply is turned on.

Was the correct number of garments selected for the

Quick Refresh Cycle?

Check that you selected the correct Number of Garments

feature equal to the number of garments refreshed.

Was the dryer overloaded?

Dry smaller loads that can tumble freely. Smaller loads of

Number of Garments yield best results with Quick Refresh

Cycle. Results may also vary depending on fabric type. This

cycle is best for reducing wrinkles and odors from loads

consisting of wrinkle-free cotton, cotton polyester blends,

common knits, and synthetics.

Odors

Have you recently been painting, staining, or varnishing in

the area where your dryer is located?

If so, ventilate the area. When the odors or fumes are gone

from the area, rewash and dry the clothing.

To remove odors left in garments after wearing, select Quick

Refresh for small loads of garments. This cycle is best for

reducing wrinkles and odors from loads consisting

of wrinkle-

free cotton, cotton polyester blends, common knits, and

synthetics.

Is water connected to the dryer?

Check that water inlet hose is connected to both the faucet

and dryer's water inlet valve. Check that the water supply is

turned on.