- ページ 7

ドライヤー Whirlpool YCEP2760KQ2のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Whirlpool YCEP2760KQ2 27 ページ。 Commercial dryer gas or electric

ページを印刷する

Electrical

requirements

If codes permit and a separate

ground wire is used, it is

recommended

that a qualified

electrician

determine

that the ground

path is adequate.

Important: Observe all governing

codes

and ordinances.

A four-wire

or three-wire

(Canada:

four-wire

only), single-phase,

1201240-

volt, 60-Hz, AC-only

electrical

supply

(or four-wire

or three-wire,

120/208-

volt, if specified

on the model/serial

rating plate)

is required

on a

separate,

30-ampere

circuit, fused on

both sides of the line, A time-delay

fuse or circuit

breaker

recommended,

Recommended

ground method

In U.S.:

It is the personal

responsibility

and

obligation

of the customer

to contact

a qualified

electrician

to assure that

the electrical

installation

is adequate

and in conformance

with the

National

Electrical

Code,

ANSI/NFPA

70", and all local codes and

ordinances,

In Canada:

It isthe personal

responsibility

and

obligation

of the customer

install the dryer in accordance

with CAN 1-B149 installation

codes**

and all national

or local

codes.

Canadian

models are equipped

with a four-wire,

30-amp

rated

flexible-type

power

cord. The

power

cord must be plugged

into

a mating

30-amp

receptacle.

(NEMA type 14-30R).

Copies

of the standards

listed above

may

be obtained

from:

* National

Fire Protection

Association

One Baited/march

Park

Quincy,

Massachusetts

02269

**CSA International

8501 East Pleasant

Valley Road

Cleveland,

Ohio 44131 _75

Now Start...

Excessive Weight Hazard

Use two or more people to move

and install dryer.

Failure to do so can result in

back or other injury.

With dryer in laundry area...

exhaust_

vent

sylle

'u:_°nnectbox

mTake tape

off front corners of

dryer, Open dryer and remove the

literature

and parts packages,

Wipe

the interior of the drum thoroughly

with a damp

cloth,

mTake two of the cardboard

corners from the carton

and place

them on the floor in back of the dryer,

Firmly grasp the body of the dryer

and gently

lay it on its back on the

cardboard

corners,

mWith one of the legs in hand,

check

the ridges for a diamond

marking, That's how far the leg is

supposed

to go into the hole,

mStaff to screw the leveling

legs

into the holes by hand,

(Use a small

amount

of liquid detergent

lubricate

the screw threads

so it is

easier to turn the legs,) Use a 1-inch

wrench

or socket wrench

to finish

turning

the legs until you reach the

diamond

mark,

Now stand the dryer up,

Slide dryer onto cardboard

hardboard

before moving across floor

to avoid damaging

floor covering.

Electrical Shock Hazard

Disconnect power before

servicing,

Replace all parts and panels

before operating,

Failure to do so can result in

death or electrical shock,

m Remove the service door of the

meter case, Lift

the service door

up at the back

and remove,

Install money-

accepting

device,

(Refer to

manufacturer's

instructions

for proper

installation,)

For dryers using coin slides, use

adapter

kit supplied

with dryer,

Replace

the meter case service

door, Put the coin vault with lock and

key the meter case opening,

m Move dryer close to final

position,

Remove

cardboard

hardboard

from under dryer,

Page 7