- ページ 18

ドライヤー Whirlpool YWED72HEDWのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool YWED72HEDW 41 ページ。 Electronic dryer

ページを印刷する

Troubleshooting

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help –

If you experience

Dryer Results (cont.)

Odors

Load too hot

Dryer Displaying Code Message or Cycle Status Indicator Lights Up

"PF" (power failure)

"L2" Diagnostic Code

(low or no line voltage

condition)

"F# E#" (F1 E1, F3 E1, etc.)

variable service codes

Check Vent indicator is lit

"Loc" or "Lc"

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Possible Causes

Recent painting, staining, or varnishing

in the area where your dryer is located.

Steam models only: For steam cycles,

the water is not properly connected

with the dryer.

Odors are left in garments after

wearing.

Load removed before cooldown

portion of cycle complete.

Using Timed Dry cycle with a high

temperature setting.

The drying cycle has been interrupted

by a power failure.

There may be a problem with your

home power supply, keeping the

dryer's heater from turning on.

The dryer is in need of service.

The lint screen or vent is clogged; the

vent is crushed or kinked or has too

many turns.

The Control Lock is enabled.

Solution

Ventilate the area. When the odors or fumes are gone from

the area, rewash and dry the clothing.

Make sure water is connected to the dryer. Check that water

inlet hose is connected to both the faucet and dryer's water

inlet valve. Check that the water supply is turned on.

Steam models only: To remove odors left in garments after

wearing, select Steam Refresh. This cycle is best for reducing

wrinkles and odors from dry loads consisting of wrinkle-

free cotton, cotton-polyester blends, common knits, and

synthetics.

Allow the dryer to complete the cooldown portion of the

cycle before removing the load.

Select an Automatic Cycle with a lower heat setting to avoid

overdrying the load.

Touch and hold START to restart the dryer. NOTE: The

Control Lock function may be enabled when recovering

from a power failure. To unlock the control, touch and hold

CONTROL LOCK for at least 3 seconds.

The dryer will continue to run when this diagnostic code is

present. Touch any pad to clear the code from the display

and return to the estimated time remaining.

NOTE: This error will only show during the initial installation.

Try the following:

Check to see if a household fuse has blown or circuit breaker

has tripped. Electric dryers use two household fuses or

breakers. Replace the fuse or reset the circuit breaker.

Confirm that the power cord is properly installed. Refer to

the Installation Instructions for details.

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, consult a qualified electrician.

If a code beginning with an "F" appears in the display,

alternating between F# and E#, the dryer control has

detected a problem that requires service. Call for service.

The dryer will continue to run when this indicator is lit.

Try the following:

• Clean lint screen.

• Check to see if the vent run from the dryer to the wall is

crushed or kinked.

• Confirm that the vent run from the dryer to the wall is free

of lint and debris.

• Confirm that the exterior vent exhaust hood is free of lint

and debris.

• Confirm that your vent system falls within the

recommended run length and number of elbows for the

type of vent you are using. Refer to "Plan Vent System" in

the Installaton Instructions for details.

• Select a Timed Dry heated cycle, and restart the dryer.

• If the indicator remains lit, have your entire home venting

run cleaned.

Touch and hold CONTROL LOCK for 3 seconds to unlock

the controls of the dryer. During this time the LED Display

will count down 3-2-1. When the Control Lock is disabled,

the LED Display will clear.