- ページ 11

ドライヤー Whirlpool YWED9270XR1のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool YWED9270XR1 28 ページ。 Duet / duet steam electronic dryer

ページを印刷する

First try the solutions suggested here and possibly avoid the cost of a service call...

Dryer Operation

Dryer will not run

■

Is the dryer door firmly closed?

■

Was the Start/Pause button firmly pressed?

Large loads may require pressing and holding the Start/Pause

button for 2-5 seconds.

■

Has a household fuse blown, or has a circuit breaker

tripped?

There may be 2 household fuses or circuit breakers for the

dryer. Check that both fuses are intact and tight, or that both

circuit breakers have not tripped. Replace the fuse or reset the

circuit breaker. If the problem continues, call an electrician.

■

Is the correct power supply available?

Electric dryers require 240-volt power supply. Check with a

qualified electrician.

■

Was a regular fuse used?

Use a time-delay fuse.

Unusual sounds

■

Has the dryer had a period of non-use?

If the dryer hasn't been used for a while, there may be a

thumping sound during the first few minutes of operation.

■

Is a coin, button, or paper clip caught between the drum

and front or rear of the dryer?

Check the front and rear edges of the drum for small objects.

Clean out pockets before laundering.

■

Are the four legs installed, and is the dryer level front to

back and side to side?

The dryer may vibrate if not properly installed. See the

Installation Instructions.

■

Is the clothing knotted or balled up?

When balled up, the load will bounce, causing the dryer to

vibrate. Separate the load items and restart the dryer.

No heat

■

Has a household fuse blown, or has a circuit breaker

tripped?

The drum may be turning, but you may not have heat. Electric

dryers use 2 household fuses or circuit breakers. Replace the

fuse or reset the circuit breaker. If the problem continues, call

an electrician.

Dryer displaying code message

■

"PF" (power failure), check the following:

Was the drying cycle interrupted by a power failure?

Press and Hold to START to restart the dryer.

■

"F# E#" (F1 E1, F3 E1, etc.) variable service codes:

If a code beginning with an "F" appears in the display,

alternating between F# and E#, the dryer control has detected

a problem that requires service. Call for service.

TROUBLESHOOTING

For additional recommendations, refer to your Installation Instructions.

Dryer Results

Clothes are not drying satisfactorily, drying times are too

long, or load is too hot

■

Is the lint screen clogged with lint?

Lint screen should be cleaned before each load.

■

Has the Air Dry temperature setting been selected?

Select the right temperature for the types of garments being

dried. See "Air Dry."

■

Is the load too large and heavy to dry quickly?

Separate the load to tumble freely.

■

Is the exhaust vent or outside exhaust hood clogged with

lint, restricting air movement?

Run the dryer for 5-10 minutes. Hold your hand under the

outside exhaust hood to check air movement. If you do not

feel air movement, clean exhaust system of lint or replace

exhaust vent with heavy metal or flexible metal vent. See the

Installation Instructions.

■

Are fabric softener sheets blocking the grille?

Use only one fabric softener sheet, and use it only once.

■

Are drying times too long or are clothes too dry?

Automatic cycle default settings may have been changed. See

Changing the Automatic Cycle Default Settings.

■

Is the exhaust vent the correct length?

Check that the exhaust vent is not too long or has too many

turns. Long venting will increase drying times. See the

Installation Instructions. See also Changing the Automatic

Cycle Default Settings, if you are unable to shorten the vent

length.

■

Is the exhaust vent diameter the correct size?

Use 4" (102 mm) diameter vent material.

■

Is the dryer located in a room with temperature below 45ºF

(7ºC)?

Proper operation of dryer cycles requires temperatures above

45ºF (7ºC).

■

Is the dryer located in a closet?

Closet doors must have ventilation openings at the top and

bottom of the door. The front of the dryer requires a minimum

of 1" (25 mm) of airspace, and, for most installations, the rear

of the dryer requires 5" (127 mm). See the Installation

Instructions.

Cycle time too short

■

Is the automatic cycle ending early?

The load may not be contacting the sensor strips. Level the

dryer.

Change the dryness level setting on Automatic Cycles.

Increasing or decreasing the dryness level will change the

amount of drying time in a cycle. If loads are consistently

ending too early, see also Changing the Automatic Dry Default

Settings.

Lint on load

■

Is the lint screen clogged?

Clean lint screen. Check for air movement.