- ページ 10

ドライヤー Whirlpool YWED9500TU0のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool YWED9500TU0 44 ページ。 Electronic electric dryer
Whirlpool YWED9500TU0 にも：マニュアル (17 ページ)

ページを印刷する

Vent s ystem chart

NOTE: Side andbottom exhaust installations

have a90 ° turn

inside thedryer. Todetermine maximum e xhaust length, add one

90 °turn tothechart.

Number of Type of

Boxor

Angled

g0 °turns

vent

Iouvered

hoods

or elbows

hoods

Rigid metal

64ft (20m)

58ft (17.7 m)

Flexible m etal 36ft (11m)

28ft (8.5 m)

Rigid metal

54ft (16.5 m) 48ft (14.6 m)

Flexible m etal 31ft (9.4 m)

23ft (7m)

Rigid metal

44ft (13.4 m) 38ft (11.6 m)

Flexible m etal 27ft (8.2 m)

19ft (5.8 m)

Rigid metal

35ft (10.7 m) 29ft (8.8 m)

Flexible m etal 25ft (7.6 m)

17ft (5.2 m)

Rigid metal

27ft (8.2 m)

21ft (6.4 m)

Flexible m etal 23ft (7m)

15ft (4.6 m)

1. Install exhaust hood. Use caulking compound toseal exterior

wall o pening a round e xhaust hood.

2. Connect vent t oexhaust hood. Vent m ust f itinside exhaust

hood. Secure v ent t oexhaust hood with4"(10.2 cm)clamp.

3. Run vent t odryer l ocation. Use thestraightest path possible.

See "Determine

vent p ath" in"Plan Vent System." Avoid 90 °

turns. U se clamps t oseal a ll j oints. D onotuseduct t ape,

screws o rother f astening devices thatextend i nto theinterior

ofthevent t osecure v ent.

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. To protect the floor, use a large flat piece of cardboard from

the dryer carton. Place cardboard under the entire back edge

of the dryer.

2. Firmly grasp the body of the dryer (not the console panel).

Gently lay the dryer on the cardboard.

See illustration.

Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to

finish turning the legs until the diamond marking is no longer

visible.

5. Place a carton corner post from dryer packaging under each

of the 2 dryer back corners. Stand the dryer up. Slide the

dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in

dryer. If connecting to existing vent, make sure the vent is

clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Check that the vent is secured

to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible

gas line.

4. Once the exhaust vent connection is made, remove the

corner posts and cardboard.

The dryer must be connected to the cold water faucet using the

new inlet hoses. Do not use old hoses.

1. Turn cold water faucet off and remove washer inlet hose.

2. Remove old rubber washer from inlet hose and replace with

new rubber washer provided. If space permits, attach the

brass female end of the "Y" connector to the cold water

faucet.

NOTE: If "Y" connector can be attached directly to cold water

faucet, go to Step 6. If "Y" connector cannot be attached

directly to the cold water faucet, the short hose must be

used. Continue with Step 3.

3. Attach short hose to cold water faucet. Screw on coupling by

hand until it is seated on faucet.

4. Using pliers, tighten the couplings with an additional two-

thirds turn.

NOTE: Do not overtighten.

Damage to the coupling can

result.

5. Attach "Y" connector to brass male end of small hose. Screw

on coupling by hand until it is seated on connector.

6. Attach straight end of long hose to "Y" connector.

7. Attach washer cold inlet hose to other end of "Y" connector.

Screw on coupling by hand until it is seated on connector.