- ページ 13
電動おもちゃの車 Calandra Racing Concepts Carpet Knife Generation X SeriesのPDF 組立マニュアルをオンラインで閲覧またはダウンロードできます。Calandra Racing Concepts Carpet Knife Generation X Series 18 ページ。
ページを印刷するBag 8
Differential Axle
1 - Locate the tree of ride height inserts [88]. Select an insert that will work best with your tire size
of ride height with 2.20" tires)
2 - Insert a 1/4" x 3/8" [89] Flanged Bearing into each of the ride height spacers.
3 - Now insert the ride height spacers into the rear pod plates with the bearings up.
90
89
97
Bag 9
Differential
** Balls in outer ring of holes in gear **
95
D
A
-
IFF
SSEMBLY
CONTINUED
The diff spacer [100] has a small machined
lip on one side, point that lip toward the
bearing. Now, place the spring washer [101]
so that the cone points away from the gear.
The outside of the washer should be
against the diff spacer, and the inside of the
washer should be against the diff nut [102],
which now goes on last. *Be sure the 2 "D"
rings have settled into their notches. Just
snug the nut so the parts stay together on
the diff axle. Correct diff tension needs to
be set with tires on the car. We will do this
later.
88
Ride Height Inserts
. Save the left over inserts as you will use these to adjust rear ride height as the tires wear.
4 - Slide the rear axle [90] through two 1/4" shims [91] and into the 2 rear pod bearings.
5 - On the protruding axle, slip two more 1/4" shims over the axle. Then slip the hub [92] on as shown in the picture.
91
6 - Lock the hub in place with the two 4-40 x 3/8" steel cap head screws [93] so that the axle has a
very small amount of side to side play in it. The thickness of 2 sheets of paper is plenty. You don't
88
want excessive play here, you're just making sure to not pinch the bearings.
Diff Ring
1/4" x 3/8"
Plain Bearing
98
1
94
...
98
1/4" x 3/8"
1/4" Shim
Flanged Bearing
89
91
88
91
93
89
1/4" x 3/8"
Flanged Bearing
Diff Spacer
89
100
1 - I
NSTALL AND GREASE THE DIFF BALLS
Pop the 1/8" diff balls [94] into each of the outer ring of holes in the
diff gear [95]. The balls snap into the socket. Place a small dab of
silicone diff grease [96] on each ball. Use very little!
96
2 - D
A
IFF
SSEMBLY
*(Holding the car on it's side, with the rear axle pointing upright will
ease assembly of the diff.) Place 1 diff ring [97], and then a 1/4" x
3/8" plain bearing [98] over the end of the axle. Align the diff ring so
97
that it notches into the axle flange. Place the assembled gear with
the greased diff balls over the axle and push it down over the plain
bearing. Next, insert the other plain bearing into the back of the diff
hub [99]. Then, align the second diff ring with the notch on the back
of the diff hub. *(place a small dab of the diff grease on the hub first
to hold the ring in place.)* Now, slide the hub, bearing, & diff ring
down over the axle. Next, slide a flanged bearing [89] over the axle
and into the front of the diff hub.
4-40 x 3/8"
Steel Socket Cap
93
(example - the #2 spacers will give you about 5mm
92
Spring Washer
Nylon Diff Nut
101
Lip
102
99
100
89
101
Small lip
toward bearing
102
12