- ページ 4

換気フード Whirlpool 2510498のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool 2510498 28 ページ。 Wall-mount canopy range hood

ページを印刷する

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

Level

■

Drill with 1¼" (3.0 cm), 3/8" (9.5 mm), and 5/16" (7.9 mm)

■

drill bits

Pencil

■

Wire stripper or utility knife

■

Tape measure or ruler

■

Pliers

■

Caulking gun and weatherproof caulking compound

■

Vent clamps

■

Jigsaw or keyhole saw

■

Flat-blade screwdriver

■

Metal snips

■

Phillips screwdriver

■

Parts needed

Home power supply cable

■

1/2" (1.3 cm) UL listed or CSA approved strain relief

■

3 UL listed wire connectors

■

For vented installations, you will also need:

1 wall or roof cap

■

Metal vent system

■

For non-vented (recirculating) installations, you will also

need:

Recirculation Kit - See "Assistance or Service" section to

■

order.

6" (15.2 cm) dia. round metal vent duct - length required is

■

determined by ceiling height.

Parts Supplied

Remove parts from packages. Check that all parts are included.

Hood canopy assembly with blower, light bulbs, and canopy

■

glass already installed

Vent transition with back draft dampers installed

■

Metal grease filter

■

Vent cover support bracket

■

Mounting template

■

2-piece vent cover

■

Air deflector (for non-vented [recirculating] installations only)

■

2 - 3.5 x 9.5 mm T10 screws

■

4 - 4.2 x 8 mm T20

screws

■

6 - 5 x 45 mm mounting screws (for 8 x 40 mm wall anchors)

■

2 - 8 x 40 mm wall anchors

■

4 - 10 x 60 mm wall anchors

■

4 - 5.4 x 75 mm screws (for 10 x 60 mm wall anchors)

■

T10 Torx

adapter

®†

■

T20

Torx

adapter.

®†

■

†

TORX and T20 are trademarks of Acument Intellectual Properties, LLC.

INSTALLATION REQUIREMENTS

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial/rating plate. The model/serial/

rating plate is located behind the left filter on the rear wall of the

vent hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) Installation see "For non-

vented (recirculating) installation only" in the "Connect Vent

System" section. Recirculation Kit Part Number W10294733 is

available from your dealer or an authorized parts distributor. All

openings in ceiling and wall where canopy hood will be installed

must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title

24 CFR, Part 328 (formerly the Federal Standard for Mobile

Home Construction and Safety, Title 24, HUD, Part 280) or when

such standard is not applicable, the standard for Manufactured

Home Installation 1982 (Manufactured Home Sites, Communities

and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with

local codes.

Product Dimensions

10⁷⁄₈"

4⁷⁄₈"

(27.6 cm)

(12.3 cm)

13³⁄₁₆"

(33.5 cm)

30" (76.2 cm) or

36" (91.4 cm)

*For non-vented (recirculating) installations

**For vented installations

5¹⁵⁄₁₆"

(15.0 cm)

*27⁵⁄₁₆" (69.4 cm) min.

45¹⁵⁄₁₆" (116.6 cm) max.

21"

(53.3 cm)

14³⁄₄"

**27⁵⁄₁₆" (69.4 cm) min.

(37.6 cm)

42" (106.7 cm) max.

1¹³⁄₁₆"

(4.6 cm)

19¹¹⁄₁₆" (50.0 cm)