- ページ 8

換気フード Whirlpool 30 " Eye-Level Gas RangeのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool 30 " Eye-Level Gas Range 28 ページ。 Freestanding gas range with self-cleaning oven
Whirlpool 30 " Eye-Level Gas Range にも：取付説明書および取扱説明書 (32 ページ), 取付説明書 (11 ページ), 取付説明書 (11 ページ), インストレーション・インストラクション (5 ページ), 取付説明書 (28 ページ), 取付説明書 (48 ページ), 取付説明書 (32 ページ), 取付説明書 (12 ページ), インストレーション・インストラクション (5 ページ), 取付説明書 (7 ページ), インストレーション・マニュアル (7 ページ), 取付説明書 (7 ページ), インストレーション・インストラクション (5 ページ), 取付説明書 (7 ページ), 取付説明書 (10 ページ)

7. Drill Electrical Opening

Using a 1¹⁄₄" (3 cm) drill bit, drill the hole in the dot marked

previously at the electrical strain relief.

OPTIONAL: Using a ¹⁄₈" (3 mm) drill bit, drill pilot holes for the

dots marked previously at each mounting tab at an approximate

45° angle in an upward direction.

8. Prepare Range Hood Vents and

Mounting Tabs

Install Strain Relief

Install a UL Listed/CSA Approved ¹⁄₂" (13 mm) strain relief (A).

Mounting Tabs

Start a #8-18 x ⁵⁄₈" (4.2 x 16 mm) truss-head screw into the

mounting tab (F) on each side of the range hood as shown in

the inset. Insert the screws approximately 2 turns into the

mounting tab holes.

Non-vent (Recirculating) Installations

Using a #2 Phillips screwdriver remove the 2 screws and

remove the top, front rectangular vent cover (E). Go to Step

12.

3¹⁄₄" x 10" (8.3 x 25.4 cm) Rectangular Vent Installations

For top vent installations, remove the top, rectangular vent

knockout (C).

For wall vent installations, remove the rear rectangular vent

knockout (B).

7" (17.8 cm) Round Vent Installations

Remove both top knockouts (C and D).

9. Attach Vent Damper or Transition

3¹⁄₄" x 10" (8.3 x 25.4 cm) Rectangular Vent Damper

Using (2) short Phillips head screws, install the 3¹⁄₄" x 10"

(8.3 x 25.4 cm) rectangular damper over the top or rear vent

knockout removed in Step 8.

NOTE: If the wall cap used has a damper and it interferes

with the rectangular damper, remove the rectangular damper

flap.

7" (17.8 cm) Round Vent Mounting Plate

Using (2) short Phillips head screws, install the 7" (17.8 cm)

round vent mounting plate over the vent knockouts removed

in Step 8. Position the wide flange (C) to the front.

NOTE: An optional 7" (17.8 cm) round damper (A), Part

Number W10355451, and a 7" (17.8 cm) round vent mounting

plate (B), Part Number W10388168, are available as

accessories. For information on ordering, see the "Assistance

or Service" section.

If installing the optional round damper, position it over the

round vent mounting plate.