- ページ 11

換気フード Whirlpool AKR 509 IXのPDF 取付・使用説明書をオンラインで閲覧またはダウンロードできます。Whirlpool AKR 509 IX 21 ページ。

ページを印刷する

carbon filters (on the basis of the model possessed). The

fumes and steam are recycled into the kitchen through upper

grill H.

Attention! If the hood is not supplied with carbon filter,

then it must be ordered and mounted.

Installation

Preparing for installation

WARNING:

this is a heavy product; the hood

should only be lifted and installed by two or more people.

The minimum distance between the supporting surface for the

cooking equipment on the hob and the lowest part of the

range hood must be not less than 50cm from electric cookers

and 65cm from gas or mixed cookers.

If the instructions for installation for the gas hob specify a

greater distance, this must be adhered to.

Electrical connection

The mains power supply must correspond to the rating

indicated on the plate situated inside the hood. If provided with

a plug connect the hood to a socket in compliance with current

regulations and positioned in an accessible area. If it not fitted

with a plug (direct mains connection) or if the plug is not

located in an accessible area apply a double pole switch in

accordance with standards which assures the complete

disconnection of the mains under conditions relating to over-

current category III, in accordance with installation

instructions.

Warning! Before re-connecting the hood circuit to the mains

supply and checking the efficient function, always check that

the mains cable is correctly assembled.

Mounting

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take

the weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

This type of cooker hood must be fixed to the ceiling.

Fig. 5-6-7

Remove the grease filter/s and the carbon filter frame.

Adjust the extension of the support structure of the hood.

The final height of the hood depends on this adjustment.

Note: In some cases the upper section of the trellis is

fixed to the lower section with 1 or more screws. Check

and remove them temporarily to allow the adjustment of

the support structure.

Fix the two sections with a total of 16 screws (4 per

corner).

Apply 1 or 2 brackets as reinforcement for extensions

greater than the minimum (on the basis of what is

envisaged as equipment).

Note: 1 bracket can already be fixed to the trellis

temporarily with 2 screws during transport. Move it into

the desired position or complete fixing it with 6 additional

screws, as follows:

a. Slightly stretch the brackets to be fixed in order to be

able to apply them outside the structure.

b. Position the reinforcement bracket immediately above

the fixing point of the two sections of the structure and fix

with a total of 8 screws (2 per corner).

Fix the second reinforcement bracket, if supplied, in a

position midway between the first reinforcement bracket

and the upper side of the trellis and fix with 8 screws (2

per corner).

Note: check that there is no obstacle to an easy fixing of

the discharge tube (aspiration version) or the deflector

(filtering version) in positioning the reinforcement

bracket(s).

Hook the hood to the trellis and make sure that it is

perfectly hooked up. Screw the 16 screws up (4 per

corner) tightly to hook the hood to the trellis.

Apply the perforation diagram of the cooking top to the

ceiling vertically (the centre of the diagram must

correspond to the centre of the cooking top and the sides

must be parallel to the sides of the cooking top – the side

of the diagram with the word FRONT corresponds to the

control panel side). Prepare the electrical connection.

Make holes as indicated (6 holes for 6 wall dowels – 4

dowels for hooking), and screw 4 screws into the external

holes, leaving a space of about 1 cm between the head

of the screws and the ceiling.

Hook the trellis to the ceiling with 4 screws, see operation

4).

Screw the 4 screws up tightly.

Introduce and screw another 2 screws tightly into the

holes for fixing the safety elements remaining free.

9. Introduce a discharge tube inside the trellis and connect to

the connecting ring of the motor space (discharge tube

and bands not supplied). The discharge tube must be

long enough to reach the exterior (aspiration version) or

the deflector (filtering version).

10. Only for filtering version: mount deflector F onto the

trellis and fix it with 4 screws to the apposite bracket and

finally connect the discharge tube to the connection ring

placed on the deflector.

11. Connect the electricity to the domestic power. Power

must be supplied only after the installation has been

completed.

12. Put the nuts equipped with fixing hooks inside the

sections of the upper and lower flues in correspondence

with the rectangular slots. A total of 14 nuts should be

mounted.

13. Couple the two upper sections of the flue to cover the

trellis so that one of the slits present on the sections is

placed on the same side of the command panel and the

other on the opposite side.

Screw the two sections up with 8 screws (4 per side –

also see the plan diagram for coupling the two sections).

14. Fix the upper flue set to the trellis near the ceiling with

two screws (one per side).

15. Couple the two lower sections of the flue to cover the