- ページ 6
換気フード Whirlpool GZ8330 Series andのPDF 取付説明書および取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool GZ8330 Series and 10 ページ。 30" and 36" convertible range hood
Whirlpool GZ8330 Series and にも： 取扱説明書 (20 ページ)
ページを印刷する
keyhole
smot
front
of hood
I
3®
Lift the range hood up
under cabinet and determine
final
position.
Mark on the underside
of cabinet the location of the four
keyhole mounting
slots. Set
range hood aside on a protected
surface.
drill pilot ho_e
_.
Use 1/8" (or 3 rnm) drill bit
and drill 4 pibt
hobs as shown.
Make electrical
Electrical Shock Hazard
Disconnect
power before making
electrical
connections.
Connect ground wire to green
ground screw in terminal box.
Failure to do so can result in
death or electrical shock.
b_ower
/_
bmower
disaharge
_
discharge
i
i
i
=
""
i
i
_.
•
1
horizonta_
vent
vertica_
vent
2[]
Reinstall blower.
Vented installations:
Reinstall
blower. Do not grasp
blower
by blower wheels.
Position
blower
so that blower discharge
lines up with damper/vent
connector
and slip rods into
mounting
brackets on blower
assembly.Tighten
knurled
nuts
securely
and reconnect
blower
plug.
Non=vented
installations:
front
homes
1/4"
(64 ram)
I
5
[] Remove the 4 hood
mounting screws from the parts bag
and install in pilot holes. Leave
screw heads away from filler
strips or cabinet bottom about
1/4" (6.4 cm)
6[]
if using direct wiring, make
sure power is disconnected, and pull
about 12" (30 cm} of wire through
wail or cabinet and into opening.
7[]
Lift range hood into final
position,
feeding
electrical
wire
through
wiring
opening.
Position the
range hood so that the large end of
the keyhole
slots are over the
screws.Then
push the hood toward
the wail so that the screws are in the
neck of the slots.Tighten
mounting
screws to cabinet,
making
sure
mounting
screws are in narrow
neck
of slots. Make sure that damper
blade, if used, rotates
up and down
freely.
8
[] Connect ventwork
to hood.
Seal joints with duct tape to make
the secure and air tight.
green or bare
e_eetrica_
ground wire
connector
19_
Make
electrical
connections.
Install
Iocknut
on
electrical
connector
and tighten
securely.
Connect
white
to white
and black to black wires
using
twist=on
connectors.
Connect
green
or bare ground
wire
to the
green
ground
screw,.
Using a U.L.qisted power
supply cord-connection
kit
(U.S. only):
Folbw Power Cord Kit instructions for
connecting wiring.
[_[] Replace wiring
box cover
and screw's. Make sure that wires
are not pinched between cover
and hood.
lm
Install two 75 watt max.
bulbs, or one 75 watt and one 25
watt bulb for night=light
use. Install
25 watt bulb in right=hand
socket.
Reinstall
blower. Do not grasp
blower
by blower wheels.
Move
mounting
rods to front holes in
hood support channels.
Position
blower
so that blower
discharge
lines up with Iouvered opening
on
hood front.
Slip rods into mounting
brackets
and tighten
knurled nuts securely.
Reconnect
blower
plug.
_ouver
cover
Remove louver cover on control
panel. Pry cover off with
screwdriver
or knife.
23m
Reinstall bottom
cover
(see Step 6).
To get the most
efficient
use from
your
new range
hood,
read the "Use
and
Care mnformation"
section.
Keep your Whirmpooi
mnstaHation
mnstruetions
and
Use and Care Guide dose
to range hood for easy
reference.