- ページ 6

換気フード Whirlpool RH4830XLQ1のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool RH4830XLQ1 10 ページ。 30/36" (76.2/91.4 cm) convertible range hood installation instructions
Whirlpool RH4830XLQ1 にも：パーツリスト (1 ページ)

ページを印刷する

keyhole

s_ot

front

of hood

® Lift the range hood up under

cabinet and determine

finaU

position.

Mark on the underside

of cabinet the Uocadon of the four

keyhob

mounting

sbts. Set

range hood aside on a protected

surface.

drill

pilot

hole

® Use 1/8" (or 3 ram) ddH bit

and drill 4 pibt

hobs

as shown.

1/4"

(6.4 rnm)

Remove the 4 hood

mounting screws from the parts bag

and install in pilot hoUes. Leave

screw' heads away from shim

strips about 1/4" (6.4 cm)

1[]

if using direct wiring, make

sure power is disconnected, and pull

about 12" (30 cm) of wire through

wail or cabinet and into opening.

installations,

one end of the vent

connector

may need to be

trimmed

to clear the electrical

strain relief.

Make electrical

Electrical Shock Hazard

Disconnect

power before making

electrical connections.

Connect ground w{re to green

ground screw in terminal box.

Failure to do so can result in

death or electricaJ shock.

5®

Depress both sides of the

light lens until tabs disengage

from slots in hood and remove

lens.

Install two 40 watt (maximum)

type Aq5 appliance

bulbs.

Reinstall

light

lens. Depress

both

sides

of lens,

insert

tabs

into slots

and release.

6[]

For non-vented

installations:

Grasp tab at front

center of filter. Push toward

back

to release filter from spring clips

at front. Puil down then froward

to remove aluminum

mesh filter.

Install non-vented

filter

(purchased

separately)

inserting

into channel at back of

compartment.

Grasp tab and pull

forward

so that filter snaps under

spring dips at front.

To get the most

efficient

use from

your

new range

hood,

read the "Use

and

Care mnformation"

section.

Keep your Whirlpool

mnstaHation

instructions

and

Use and Care Guide

to range hood for easy

reference.

2[]

Lift range hood into final

position,

feeding

electrical

wire

through

wiring

opening.

Position

the

range hood so that the large end of

the keyhole

slots are over the

screws.Then

push the hood toward

the wail so that the screws are in the

neck of the slots.Tighten

mounting

screws to cabinet,

making

sure

mounting

screws are in narrow

neck

of slots. Make sure that damper

blade, if used, rotates

up and down

freely.

13m

Connect ventwork

to hood.

Seal joints with duct tape to make

the secure and air tight.

Note:

Damper/vent

connector

and

round

vent

plate

can be installed

up to 1/2" (12.7 ram)

on either

side of hood

center

if ventwork

off-center,

in extreme

off-center

green

groun¢

screw

14"[] Directwiring:

Connect the white and black wires

of the power supply cable to the

white and black leads in the hood

with twist-on

connectors.

Connect the power supply ground

wire to the green ground

screw'

inside the terminal

bex.

Use caulking

to seal wire opening.

Replace terminal

box cover.

Using a U.L.-listed power

supply cord-connection

kit

(U.S. only}:

FoHew Power Cord }(it instructiens for

connecting wi_ng.