- ページ 10

換気フード Whirlpool UXW7230BSSのPDF 取付説明書および取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool UXW7230BSS 32 ページ。 30-inch vented 400-cfm wall-mount canopy hood
Whirlpool UXW7230BSS にも：取付説明書および取扱説明書 (32 ページ), 取付説明書および取扱説明書 (32 ページ)

ページを印刷する

NOTE: The 7" (17.8 cm) round vent mounting plate and

3 " x 10" (8.3 x 25.4 cm) rectangular vent damper can be

installed up to 1" (2.5 cm) on either side of the hood

center to accommodate off center ductwork.

A. Vertical damper

B. 3.5 x 9.5 mm screws

If a vent damper is installed with a wall cap with damper,

check that they do not interfere with each other. Remove

the vent connector damper flap if they interfere.

Non-vented (recirculating) installations - No vent

attachments. Removal of the recirculation cover plate is

required. Remove the two screws from the recirculation

cover plate and remove.

A. Recirculation cover plate

B. Screws

Damper Flap Removal for 3¼" x 10" (8.3 x 25.4 cm) Vent

Connector

1. Bend retainer wire out of damper flap catch tab.

A. Retainer wire

B. Damper flap wire guide

C. Plastic end caps

D. Stop tabs

C. Vent knockouts

D. Horizontal damper

E. Vent connector housing

F. Foam

G. Damper flap catch tab

H. Damper flap

2. Slide retainer wire to the side to allow one end of retainer wire

to come out of the damper flap wire guide and plastic end

cap.

3. Lift end of retainer wire and slide it out of the other damper

flap wire guide and plastic end cap to remove.

4. Push the small end of the plastic end caps out of vent

connector housing.

5. Lift the damper flap out of the vent connector housing.

6. Remove the foam from the stop tab.

7. Bend the stop tabs so they are flush with the damper side

walls.

8. Discard the retainer wire, plastic end caps, damper flap and

the foam.

Power Supply Cable Installation

1. For direct wire installations, run the home power supply cable

according to the National Electric Code or CSA standards

and local codes and ordinances. There must be enough

wiring from the fused disconnect (or circuit breaker) box to

make the connection in the hood electrical terminal box.

For optional power supply cord kit installations, follow the

instructions in the "Make Electrical Connection" section.

NOTE: Do not reconnect power until the installation is

complete.

2. Remove the screw from the terminal box cover. Remove

terminal box cover and set aside.

3. Remove the power supply knockout from the top or rear of

the vent hood (depending on the incoming location of your

home power supply cable), and install a UL listed or CSA

approved

" strain relief.

A. Power supply knockout

4. Using 2 or more people, lift the hood into final position. Feed

enough electrical wire through the ½" UL listed or CSA

approved strain relief to make connections in the terminal

box. Tighten the strain relief screws.

5. Position the range hood so that the large end of the keyhole

slots are over the mounting screws. Then push the hood

toward the wall so that the screws are in the neck of the slots.

Tighten the mounting screws, making sure the screws are in

the narrow neck of slots.

6. Connect ventwork to hood. Seal joints with vent clamps or

duct tape to make secure and airtight.

7. Check that back draft dampers work properly.

A. Terminal box cover

B. Screw