- ページ 4

換気フード Whirlpool WVU17UC0FのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool WVU17UC0F 28 ページ。

ページを印刷する

Tools and Parts

Gather the required tools and parts before starting

installation. Read and follow the instructions provided

with any tools listed here.

Tools needed

Metal snips

#2 Phillips

screwdriver

Pencil

Caulking gun and weatherproof

caulking compound

Jigsaw or keyhole saw

Parts supplied

Remove parts from package. Check that all parts are included.

#8-18 x 1"

(4.2 x 25 mm)

flat-head screws

Drywall

anchors

Short Phillips

head screws

3¹⁄₄" x 10" (8.3 x 25.4 cm)

rectangular damper

Parts needed

UL Listed/CSA

Approved

wire connectors

For 3

" x 10" (8.3 x 25.4 cm) rectangular vented

installations

3¹⁄₄" x 10"

(8.3 x 25.4 cm) rectangular

metal vent system with

wall or roof cap

INSTALLATION REQUIREMENTS

Wire stripper

Flat-blade

screwdriver

Drill with ¹⁄₈"

(3 mm), ¹⁄₂"

(13 mm)

and 1¹⁄₄"

(3 cm) bits

#8-18 x ⁵⁄₈"

(4.2 x 16 mm)

truss-head screws

Mounting

brackets

120V, 75W

maximum,

type

E26 lamp

Duct tape

Optional accessories

Power

Charcoal

cord kit

filter kit

Part Number

W10355452*

W10355450*

* For information on ordering, see the "Assistance or Service"

section.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

It is the installer's responsibility to comply with installation

■

clearances specified on the model/serial/rating plate.

The model/serial/rating plate is located inside the range

hood on the left wall.

Range hood location should be away from strong draft

■

areas, such as windows, doors, and strong heating vents.

Cabinet opening dimensions that are shown must be

■

used. Given dimensions provide minimum clearance.

Consult the cooktop/range manufacturer installation

instructions before making any cutouts.

This range hood is recommended for use with cooktops

■

with a maximum total rating of 40,000 Btus or less.

Grounded electrical outlet is required. See the "Electrical

■

Requirements" section.

All openings in ceiling and wall where range hood will

■

be installed must be sealed.

These range hoods are factory set for vented installations.

■

Models that are capable of being installed as non-vented

(recirculating) require charcoal filters. See the "Assistance or

Service" section for information on ordering charcoal filters.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title

24 CFR, Part 328 (formerly the Federal Standard for Mobile

Home Construction and Safety, title 24, HUD, Part 280)

or when such standard is not applicable, the standard for

Manufactured Home Installation 1982 (Manufactured Home

Sites, Communities and Setups) ANSI A225.1/NFPA 501A,

or latest edition, or with local codes.

Product Dimensions

(5.1 cm)

4¹⁵⁄₁₆"

(12.5 cm)

(2.5 cm)

29¹⁵⁄₁₆" (76.0 cm) or

35¹⁵⁄₁₆" (91.0 cm)

Stainless steel

cleaner and

polish

Part Number

31462A*

6⁹⁄₁₆" (16.7 cm) or

9⁹⁄₁₆" (24.4 cm)

(22.9 cm)

1¹⁄₂"

18⁵⁄₈"

(3.8 cm)

(47.3 cm)

(2.5 cm)