CDプレーヤー Clarion 12799475のPDF サービスマニュアルをオンラインで閲覧またはダウンロードできます。Clarion 12799475 14 ページ。 Saab automobile genuine 6-disc cd changer

ページを印刷する

SPECIFICATIONS

CD section

Disc:

Compact disc (8 cm / 12 cm)

Separation:

More than 60 dB (at 20 kHz LPF)

S/N ratio:

More than 70 dB (at 20 kHz LPF JIS-A)

Distortion:

Less than 0.05 % (at 20 kHz LPF)

General

Optical output power: -10 to -1.5 dBm

Power supply voltage: DC13.5 V

Negative ground

Current consumption: Less than 5A

Dimensions(mm):

179 (W) x 51.5 (H) x 180.7 (D)

NOTE

We cannot supply PWB with component parts in principle.

When a circuit on PWB has failure , please repair it by com-

ponent parts base. Parts which are not mentioned in ser-

vice manual are not supplied.

Specifications and design arevsubject to change without

notice for further improvement.

COMPONENTS

PU-2426A-A

CAUTIONS

Use of controls,adjustment or performance of procedures

other than those specified herein,may result in hazardous

radiation exposure.

The COMPACT DISC player should not be adjusted or

repaired by anyone except properly qualified service per-

sonnel.

This appliance contains a laser system and is classified as

a "CLASS 1 LASER PRODUCT".

To use this model properly,read this Owner's Manual care-

fully and kep this manual for your future reference.

Clarion Co., Ltd.

50 Kamitoda, Toda-shi, Saitama 335-8511 Japan

Service Dept.: 5-66 Azuma , Kitamoto-shi, Saitama 364-0007 Japan

Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703

Service Manual

- 1 -

SAAB Automobile Genuine

6-Disc CD Changer

PU-2426A-A

Model

(Genuine No.12799475)

In case of any trouble with this player,please contact your

nearest"AUTHORIZED service station".To prevent direct

exposure to the laser beam,do not to open the enclosure.

1 2 7 9 9 4 7 5

C L A S S

L A S E R

P R O D U C T

H / W

1 2 7 9 9 4 8 7

S / W

1 2 7 9 9 4 8 8

1 2 V

N E G . G N D .

T HI S DEVI CE COMPL I ES WI T H PART 1 5 OF T HE F CC RUL ES OPE RAT I ON I S SUBJ ECT T O T HE F OL L OW I NG T WO

CONDI T I ONS: ( 1 )

T HI S DEVI CE MAY NOT CAUSE HARMF UL I NT ERF ERENCE, AND ( 2 )

ANY I NT ERF ERENCE RECEI VE D,

I NCL UDI NG I NT ERF E RENCE

I NCL UDI NG I NT ERF E RENCE T HAT MAY CAUSE UNDESI RED OPERAT I ON.

T HI S PRODUCT I ON COMPL I ES W I T H DHHS RUL ES

2 1 CF R SUBCHAPT ER J APPL I CABL E AT DAT E OF

MANUF ACT URE.

CL ARI ON CO. , L T D.

5 0 KAMI T ODA.

T ODA- SHI .

SAI T AMA- KEN.

J APAN

Y S 9 4 7 5

MANUF ACT URED:

M A D E

I N

J A P A N

P U - 2 4 2 6 A

To engineers in charge of repair or

inspection of our products.

Before repair or inspection, make sure to follow the

instructions so that customers and Engineers in

charge of repair or inspection can avoid suffering

any risk or injury.

1. Use specified parts.

The system uses parts with special safety features against

fire and voltage. Use only parts with equivalent character-

istics when replacing them.

The use of unspecified parts shall be regarded as remod-

eling for which we shall not be liable. The onus of product

liability (PL) shall not be our responsibility in cases where

an accident or failure is as a result of unspecified parts

being used.

2. Place the parts and wiring back in their original positions

after replacement or re-wiring.

For proper circuit construction, use of insulation tubes,

bonding, gaps to PWB, etc, is involved. The wiring con-

nection and routing to the PWB are specially planned us-

ing clamps to keep away from heated and high voltage

parts. Ensure that they are placed back in their original

positions after repair or inspection.

If extended damage is caused due to negligence during

repair, the legal responsibility shall be with the repairing

company.

Published by Service Dept.

298-6033-00 Dec.2002 P

Printed in Japan

T HI S DEVI CE MUST ACCEPT

X X

2 8 6 - 9 9 2 9 - 1 4

PU-2426A-A