- ページ 7
ネットワーク・ハードウェア 3Com OfficeConnect WXR100のPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。3Com OfficeConnect WXR100 10 ページ。 Secure converged networks enterprise edition
3Com OfficeConnect WXR100 にも： クイック・スタート・マニュアル (2 ページ), 製品マニュアル (15 ページ)
ページを印刷する
Using the quickstart Command (any model)
To run the quickstart command:
Attach a PC to the WX switch serial console port. (Use
1
these modem settings: 9600 bps, 8 bits, 1 stop, no
parity, hardware flow control disabled.)
Press Enter three times to display a username prompt
2
(Username:), a password prompt (Password:), and
then a command prompt such as the following:
WX1200-aabbcc>
(Each switch has a unique system name that contains
the model number and the last half of the switch's
MAC address.)
Access the enabled level (the configuration level) of
3
the CLI:
WX1200-aabbcc> enable
Press Enter at the Enter password prompt.
4
Type quickstart. The command asks you a series of
5
questions. You can type ? for more help. To quit,
press Ctrl+C.
WX1200-aabbcc# quickstart
This will erase any existing config. Continue? [n]: y
Answer the following questions. Enter '?' for
help. ^C to break out
System Name [WX1200]: WX1200-Corp
Country Code [US]: US
System IP address []: 172.16.0.21
System IP address netmask []: 255.255.255.0
Default route []: 172.16.0.20
Do you need to use 802.1Q tagged default VLAN
[Y/N]? Y: y
Specify the port number that needs to be tagged
[1-2, <CR> ends config]: 2
Using the quickstart Command (any model)
Specify the tagged value for port [2] [<CR> ends
config:] 100
Specify the port number that needs to be tagged
[1-2, <CR> ends config]:
Admin username [admin]: wxadmin
Admin password [optional]: letmein
Enable password [optional]: enable
Do you wish to set the time? [y]: y
Enter the date (dd/mm/yy) []: 08/01/07
Is daylight saving time (DST) in effect [n]: n
Enter the time (hh:mm:ss) []: 18:58:00
Enter the timezone []: PST
Enter the offset from GMT for 'PST' in hh:mm [0:0]:
-8:0
Do you wish to configure wireless? [y]: y
Enter a clear SSID to use: public
Do you want Web Portal authentication? [y] y
Enter a username with which to do Web Portal,
<cr> to exit: user1
Enter a password for user1: user1pass
Enter a username with which to do Web Portal,
<cr> to exit:
Do you want to do 802.1x and PEAP-MSCHAPv2? [y]: y
Enter a crypto SSID to use: corporate
Enter a username with which to do PEAP-MSCHAPv2,
<cr> to exit: bob
Enter a password for bob: bobpass
Enter a username with which to do PEAP-MSCHAPv2,
<cr> to exit:
Do you wish to configure access points? [y]: y
Enter a port number [1-2] on which an AP
resides, <cr> to exit: 2
Enter AP model on port 2: ap3750
Enter a port number [1-2] on which an AP
resides, <cr> to exit:
Do you wish to configure distributed access
points? [y]: y
Enter a DAP serial number, <cr> to exit:
0422700351
Enter model of DAP with S/N 0422700351: ap3750
7