- ページ 19

プリンター Xerox Versant 80 PressのPDF 顧客期待＆インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Xerox Versant 80 Press 48 ページ。 Entry production color presses
Xerox Versant 80 Press にも：安全マニュアル (26 ページ), セキュリティ・マニュアル (45 ページ)

ページを印刷する

Xerox Versant 80 Press 顧客期待＆インストレーション・マニュアル

Detailed Specifications

1 Tray Oversized High Capacity Feeder (OHCF)

Capacity

2,000 sheets (using Centerline Paper)

Sizes

Min: 7.2 x 8.3 in (182 x 210 mm), w/postcard kit 4 x 6 in

(100 x 148 mm)

Max: 13 x 19.2 in (330 x 488 mm)

Weights

52 to 300 gsm

Plain, uncoated, coated, transparencies, heavyweight,

Supported

predrilled, tabs, hole punched, labels, letterhead, postcard

Media Types

(with Tray inserter)

Finishing Specifications

Offset Catch Tray (OCT)

The Catch Tray holds a maximum of 500 sheets.

Catch Tray

 If utilizing the Catch Tray, overall productivity will decline if offsetting mode is selected. The print engine will pause printing to offset

Limitations

between sets, and then resume. Productivity loss depends on the number of sheets per set, with single-page jobs representing the worst

case (approximately 50% productivity loss)

 Sheets smaller than 6.7 inches (170 mm) in the cross-process direction (e.g. the feed edge) cannot be offset

 Sheets larger than 11.7 inches (297 mm) in the cross-process direction (e.g. the feed edge) cannot be offset

 With the EX-i/EX Fiery Print Server, the Offset Jobs box on the Finishing tab must be checked to enable offsetting.

Interface Module

TIP: The Interface Module is required with any system configuration that has one or more finishing devices, except the Offset Catch Tray (OCT), BR Finisher and

BR Booklet Finisher.

The Interface Module acts as a paper path from the press to the finishing device; it also allows communication between the press and the finishing device. The

Interface Module also cools and decurls paper as it exits the press and before it enters the finishing device.

GBC AdvancedPunch

The GBC AdvancedPunch is an inline die punch that uses modular die sets to Stack Tray Capacity: 8.5 x 11 inch (LTR) Dies enable a variety of hole punch patterns

in A4 or 8.5 x 11 inch (LTR), long-edge-fed media to support offline binding. The GBC AdvancedPunch is supported by all print servers. The GBC AdvancedPunch

requires an Interface Module as well as a High Capacity Stacker, Standard Finisher, Booklet Maker Finisher, or Standard Finisher Plus (and additional third-party

device).

GBC

 Supports media from 75-216 gsm, coated and uncoated

AdvancedPunch

 ProClick die supports media from 75-203 gsm

Specifications

 Supports tab stock no wider than 9 in.; oversized tabs may be damaged

 The GBC AdvancedPunch is able to bypass all coated and uncoated media sizes and weights that are printed on the Press

 Requires an additional electrical receptacle; refer to the

GBC

 GBC AdvancedPunch does not work in conjunction with C/Z-fold or Standard Finisher punch, staple, or booklet making

AdvancedPunch

 Hole punch position from edge of paper is not adjustable

Limitations

 Preprinted Tabs cannot be punched

 Opening the door of the GBC AdvancedPunch while the machine is running will cause the machine to jam and shut down

 Gloss coated media may not run as reliably as uncoated paper. Typically, coated papers and high area coverage exhibit increased

variability in paper handling due to lower coefficients of friction, resulting in a broader distribution of punch registration and elevated

jam rates

 Punching A4 or 8.5 x 11 in duplexed coated stocks using the GBC 3-hole punch (008R13072) is not recommended due to higher jam

rates

 Stacking may be misaligned on jobs containing tab stock; these jobs will require additional jogging before final finishing

 Due to the nature of punching holes, each punched sheet is slightly deformed, and when stacked, the edge with the holes will have an

increased height compared to the non-punched edge.

 A4 and LTR punch units are not the same and A4 and LTR die sets are not interchangeable

Customer Expectation and Installation Guide

Reduced stack quality may be experienced due to variability in the punch hole formation

When sending output to the stack tray of the High Capacity Stacker, if this stack height difference exceeds one inch, the

machine will shut down and alert the operator to unload the stacker tray. This is done to prevent a jam and will result in a

reduction of stack capacity depending on the die being used

Using the HCS tray insert (shipped with your GBC unit) will increase stack capacity. See tables below for the expected stack

ranges of the HCS stack tray for each punch die

LTR punch unit will be shipped with the 19-hole punch die

A4 unit will ship with the 21-hole punch die

Additional punch dies are available for order (see below)

Up to 3 additional die sets can be stored inside the GBC AdvancedPunch

Advanced High Capacity Feeder (Advanced HCF)

Capacity

2,000 sheets (per tray); combined capacity of 4,000

sheets (using Centerline Paper)

Sizes

Min: 7.2 x 7.2 in (182 x 182 mm), w/postcard kit 4 x 6 in

(100 x 148 mm)

Max: 13 x 19.2 in (330 x 488 mm)

Weights

52 to 350 gsm

Note: Optional performance for coated stocks is 64 –

350 gsm

Plain, uncoated, coated, transparencies, heavyweight,

Supported

predrilled, tabs, hole punched, labels, letterhead, postcard

Media Types

(with Tray inserter)

Electrical Requirements for Optional Devices

Xerox Confidential

Xerox

Versant® 80 Press