Installation Preparation Document
Xerox DocuTech 6155/6180
Customer Support
The Xerox Customer Support Center is available to provide general
information, answer questions, and take service calls. You can reach
the Customer Support Center at the following toll-free phone number:
United States
1-800-821-2797
Your Xerox Analyst will provide fee-based training upon request.
Space Requirements / Service Envelope
The components of the DocuTech 6180 system are:
• DocuSP Controller (monitor, keyboard, mouse)
• Printer
DocuTech 61xx
WIDTH
Note: The 6155 and 6180 are available with and without a stand to
support the controller. If a stand (098S04797) is ordered, it will be
positioned to the left of the printer, within the service space envelope.
If no stand is ordered, the controller will be placed on the floor to the
left of the printer in the service space envelope.
Note: The dimensions shown below provide the overall service
space required, including the space to the nearest obstruction. The
dimensions are in
inches
and are absolute minimums
With stand
Configuration
Width
6155, 6180 with
243.0"
interposer and
finisher
Electrical Requirements – DocuTech 6155 / 6180
For the printer one (1) electrical service option is available – 2-phase,
dual power cord.
Voltage
Amperage
Cycles
Receptacle Xerox Part No.
Receptacle NEMA Part No.
Receptacle Diagram
Power Cord Kit Number
Power Cord Length
Please ensure electrical, space, and supplies are available prior to equipment delivery.
701P43858
June 2005
D
E
P
T
H
Representation only.
Without stand
Depth
Width
Depth
114.0"
240.0"
114.0"
MultiSource
2-phase, dual power cord
configuration
208/240
208/240
(4 wire)
(4 wire)
50
30
60 Hz
60 Hz
600S3779
600S3277
14-50R
14-30R
98K59581
15 feet
15 feet
(for physical installation of the product only)
Electrical Requirements
Digital Front End (DFE) Controller Platform:
Line Options:
Voltage
Amperage
Cycles
15 amp Receptacle Xerox Part No.
20 amp Receptacle Xerox Part No.
Receptacle NEMA Part No.
Receptacle Diagram
•
All controller configurations require a 110VAC, 15 Amp
grounded receptacle for the outlet strip that provides
for the
controller and its peripheral devices (monitor, modem,
CDROM drive, and tape drive)
•
Adapters that eliminate the ground connection to the outlet can
not be used.
•
Xerox provides 15 feet of cabling with Teflon coating (Plenum
rated), to connect the controller to the Processor/Finisher.
Environmental Requirements
Temperature
Humidity
Heat Emission –
with Binder On
(with processor,
interposer, finisher
and binder)
Heat Emission –
with Binder Off
(with processor,
interposer, finisher
and binder)
Altitude (above
sea level)
* The system will inhibit software problems and shut down above 90
Dedicated
110
15
60 Hz
600S3704
600S3703
5 - 20R or 5 - 15R
or
receptacles
Recommended
Min.
o
o
o
68
F – 76
F
50
F
o
o
o
(20
C-24
C)
(10
C)
45% +/-10%
30% RH
-
14,185
BTU/Hr
(with vent kit)
-
13,609
BTU/Hr
(with vent kit)
Up to 6,000 ft.
-
Max.
o
85
F*
o
(29
C)
60% RH
22,165
BTU/Hr
(Running)
21,265
BTU/Hr
(Running)
9,000 ft.
o
F
ページを印刷する