- ページ 20

楽器 Yamaha Clavinova CLP-970CのPDF 参考小冊子をオンラインで閲覧またはダウンロードできます。Yamaha Clavinova CLP-970C 37 ページ。 Yamaha digital piano owner's manual
Yamaha Clavinova CLP-970C にも： (取扱説明書 (24 ページ)

ページを印刷する

MIDI Data Format

* Receiving control numbers

c = 0

BANK SELECT MSB

c = 32

BANK SELECT LSB

c = 6

DATA ENTRY MSB

c = 38

DATA ENTRY LSB

c = 7

MAIN VOLUME

c = 10

PANPOT

c = 11

EXPRESSION

c = 64

SUSTAIN

c = 66

SOSTENUTO

c = 67

SOFT PEDAL

c = 91

REVERB SEND LEVEL

c = 93

CHORUS SEND LEVEL

c = 94

VARIATION SEND LEVEL

c = 96

DATA INCREMENT

c = 97

DATA DECREMENT

*1: Used only for setting the parameters with the speciﬁed RPN.

Processing the Bank Select message is deferred until the Program Change is received. To

change the voices (including the voice banks), transmit Bank Select MSB, LSB, then Pro-

gram Change in this order as a set.

(3-2) CHANNEL MODE MESSAGES

STATUS

1011nnnn ( BnH )

CONTROL NUMBER 0ccccccc

CONTROL VALUE

0vvvvvvv

(3-2-1) ALL SOUND OFF (Only reception)

(CONTROL NUMBER = 78H , DATA VALUE = 0)

All voicing sounds on the corresponding channel(s) are muted. Note On and Hold On

Channel messages are also erased.

(3-2-2) RESET ALL CONTROLLERS (Only reception)

(CONTROL NUMBER = 79H , DATA VALUE = 0)

The following controller values are reset.

PITCH BEND CHANGE

0 (mid point)

EXPRESSION

127 (max)

SUSTAIN

0 (off)

SOSTENUTO

0 (off)

SOFT PEDAL

0 (off)

RPN

The number is not speciﬁed. The internal data does not

change.

(3-2-3) ALL NOTES OFF (Only reception)

(CONTROL NUMBER = 7BH , DATA VALUE = 0)

All notes (that are on) are turned off. If sustain or sostenuto is on, the corresponding note

does not stop voicing until sustain or sostenuto is turned off.

(3-2-4) OMNI OFF (Only reception)

(CONTROL NUMBER = 7CH , DATA VALUE = 0)

Same process as when All Notes Off message is received.

(3-2-5) OMNI ON (Only reception)

(CONTROL NUMBER = 7DH , DATA VALUE = 0)

Same process as when All Notes Off message is received.

It does not set OMNI On.

(3-2-6) MONO (Only reception)

(CONTROL NUMBER = 7EH , DATA VALUE = 0)

Same process as when All Sound Off message is received.

(3-2-7) POLY (Only reception)

(CONTROL NUMBER = 7FH , DATA VALUE = 0)

Same process as when All Notes Off message is received.

(3-3) REGISTERED PARAMETER NUMBER (RPN) (Only reception)

STATUS

1011nnnn (BnH)

RPN LSB

01100100 (64H)

RPN LSB NUMBER 0ppppppp

RPN MSB

01100101 (65H)

RPN MSB NUMBER 0qqqqqqq

DATA ENTRY MSB 00000110 (06H)

DATA VALUE

0mmmmmmm

DATA ENTRY LSB

00100110 (26H)

DATA VALUE

0lllllll

Specify the parameter with RPN MSB/LSB, then set the parameter value with data entry

MSB/LSB.

RPN

D.ENTRY

LSB MSB MSB LSB PARAMETER NAME

00H 00H

mmH ---

PITCH BEND SENSITIVITY 00H - 18H (0 - 24 semitone)

01H 00H

mmH llH

FINE TUNE {mmH,llH} = {00H,00H}-{40H,00H}-

{7FH,7FH}

(–8192*100/8192) - 0 - (+8192*100/8192)

02H 00H

mmH ---

COARSE TUNE 28H - 40H - 58H (-24 - 0 - +24 semitone)

7FH 7FH

--- ---

NULL

CLP-970

; v = 0:PANEL VOICE

; v = 0 - 127

; v = 0 - 127*1

; v = 0 - 127

; v = 0-63:OFF , 64-127:ON

; v = 0 - 127

; v = 127*1

n = 0 - 15 VOICE CHANNEL NUMBER

c = CONTROL NUMBER

v = DATA VALUE

n = 0 - 15 VOICE CHANNEL NUMBER

p = RPN LSB ( Refer to below )

q = RPN MSB ( Refer to below )

m = Data Value

l = Data Value

DATA RANGE

The RPN number is not speciﬁed.

It does not affect the internal settings.

(3-4) SYSTEM REALTIME MESSAGES (Only transmission)

(3-4-1) MIDI CLOCK

STATUS

11111000

Transmission: Transmitted in a 1/24 beat timing.

(3-4-2) START

STATUS

11111010

Transmission: The message is output when song playback on the instrument starts.

Reception: Song playback or song recording starts, depending on the state of the instru-

ment.

(3-4-3) STOP

STATUS

11111100

Transmission: The message is output when song playback on the instrument stops.

Reception: Song playback or song recording stops, depending on the state of the instru-

ment.

(3-4-4) ACTIVE SENSING

STATUS

11111110

This message is transmitted about every 200 msec.

When the instrument receives this code, it starts "sensing." If it does not receive any status

information or other data, the instrument clears the MIDI reception buffer and forces off

all voicing notes and sustain. All Control values are reset to their default settings.

(3-5) SYSTEM EXCLUSIVE MESSAGE

(3-5-1) UNIVERSAL SYSTEM EXCLUSIVE

(3-5-1-1) UNIVERSAL REALTIME MESSAGE

(3-5-1-1-1) MIDI MASTER VOLUME (Only reception)

binary

hexadecimal

Exclusive status

11110000

01111111

Universal Realtime

01111111

ID of target Device

00000100

Sub-ID #1=Device Control Message

Sub-ID #2=Master Volume

00000001

Volume LSB

0sssssss

Volume MSB

0ttttttt

11110111

End of Exclusive

11110000

Exclusive status

Universal Realtime

01111110

When N is received N=0-F, whichever is received.

0xxxnnnn

When N is transmitted N always=0.

X = don't care

00000100

Sub-ID #1=Device Control Message

Sub-ID #2=Master Volume

00000001

Volume LSB

0sssssss

Volume MSB

0ttttttt

11110111

End of Exclusive

All channel volume level is changed simultaneously.

Value "TT" is used as the master volume level. (Value "SS" is ignored.)

(F8H)

(FAH)

(FCH)

(FEH)