- ページ 28

楽器 Yamaha DTX530KのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Yamaha DTX530K 48 ページ。 Drum trigger module
Yamaha DTX530K にも：組立マニュアル (1 ページ)

ページを印刷する

7 Create Your Own Original Drum Kit

Change the Decay

This determines the Drum Voice's decay time (the time it

takes the sound to fade out after being produced).

Use the [

] button to call up the KIT6 page, then rotate the

jog dial to set the decay (-64–0–+63). Positive values produce

a crisper sound.

KIT6*~~äkick~~~˙

"~~Decay=+~8~~~‚

Change the Voice Character (Filter Set-

ting)

This determines the ﬁlter's cutoff frequency to change the

Drum Voice's character (brightness).

Use the [

] button to call up the KIT7 page, then rotate the

jog dial to set the cutoff frequency (-64–0–+63). Positive val-

ues produce a brighter sound.

KIT7*~~äkick~~~˙

"CutOffFreq=+~4‚

Set the MIDI Note Number

This determines the MIDI Note Number that is transmitted

when a signal is received from the input source. This affects

which particular percussion or drum sound of a voice will

play on a connected MIDI device.

Use the [

] button to call up the KIT8 page, then rotate the

jog dial to set the MIDI Note Number (0–127). Displays the

note number and note name (C-2–G8).

KIT8*~~äkick~~~˙

"Note=~~32/G#0~‚

* When the selected MIDI Note Number has already been

assigned to another input source, an asterisk "

Note=

played next to "

* If the same MIDI Note Number is set to more than one pad

within the same Drum Kit, the lowest numbered Input Source

will take priority. In the case of the duplicate input sources,

the same voice will be output.

If the setting is not available because of an already assigned

(Note# in use)

MIDI note number, "

use)

" is shown in the lower half of the display.

DTX500 Owner's Manual

Set the MIDI Channel

This determines the MIDI Transmit Channel for the MIDI

note on data that is transmitted when a signal is received from

the input source. This affects which particular channel will be

used when playing a voice on a connected MIDI device.

Use the [

jog dial to set the MIDI Transmit Channel (1–16).

Set the Gate Time of the MIDI Output

This determines the Gate Time (the length of time from Key

On to Key Off) for the MIDI note on data.

Use the [

jog dial to set the Gate Time (0.0s–9.9s).

Set the MIDI Key On/Off

This determines whether to recognize MIDI Key Off events

or not.

* This setting affects both layers

Use the [

jog dial to set Key On/Key Off.

enable

disable

* When this is set to "disable," some voices may sound continu-

" will be dis-

Set the Hold Mode

Every time the pad is hit, Key On and Key Off messages are

alternately sent. This means that one hit of the pad turns the

sound on and the next turns it off.

* This setting affects both layers

(# in

" or "

Use the [

jog dial to set the Hold Mode.

] button to call up the KIT9 page, then rotate the

KIT9*~~äkick~~~˙

"~~MIDI~Ch=10~~‚

] button to call up the KIT10 page, then rotate the

KIT10*~äkick~~~˙

"GateTime=0.3s~‚

not shown in the upper right corner of the display.

] button to call up the KIT11 page, then rotate the

KIT11*~äkick

"KeyOff=disable‚

............Recognizes Key Off events.

.........Does not recognize Key Off events.

ously. Press the [DRUM KIT] button to stop the sound.

not shown in the upper right corner of the display.

] button to call up the KIT12 page, then rotate the

KIT12*~äkick

"~HoldMode=off~‚

˙/¶

and

. The

indication is

˙/¶

and

. The

indication is