- ページ 2

アンプ Clark Synthesis TACTILE SOUND AW339のPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Clark Synthesis TACTILE SOUND AW339 2 ページ。 All-weather transducer
Clark Synthesis TACTILE SOUND AW339 にも：補足マニュアル (4 ページ), データシート (1 ページ), インストレーション・マニュアル (8 ページ), バイヤーズ・マニュアル (2 ページ), インストレーション・マニュアル (20 ページ), 仕様書 (1 ページ)

ページを印刷する

AW339- HOT TUB OEM INSTALL

The AW339 mounting bracket is the component used to attach the

transducer to the hot tub or spa. The mounting bracket and related hardware

come in the transducer package.

The mounting bracket assembly includes the mounting bracket, a threaded

stud, and two jam nuts (see diagram below). The mounting bracket is

secured to the underside of the hot tub. The threaded stud attaches the

transducer to the mounting bracket. The jam nuts secure the threaded stud

to the mounting bracket and transducer.

MOUNTING BRACKET ASSEMBLY

SIDE VIEW

Transducer

Jam Nuts

Threaded Stud

Mounting Bracket

When prototype testing the transducer with your hot tub, the mounting

bracket can be applied to the hot tub with epoxy. During this type of

application, do not allow the epoxy to expand into the hole where the

threaded stud is placed or you will not be able to insert the stud.

There are several factors to consider when selecting the mounting location

for the mounting bracket and transducer:

You need to insure the area allows for adequate clearance for the

transducer. The transducer should only touch the tub by way of the

mounting bracket. If the transducer comes in contact with other parts of

the hot tub it may affect the sound quality.

The location should allow for as much air space around the transducer

as possible. This will allow heat to escape from the transducer.

TOP VIEW

www.clarksynthesis.com

The location should be accessible. This will prove invaluable should the

transducer require service.

You may want to locate the transducer close to the location of the hot

tub's amplifier/sound unit to avoid additional wiring.

For larger tubs, you may want to consider mounting two transducers for

added performance.

TRANSDUCER LOCATION

CROSS-SECTION OF TUB

Once prototype testing is complete and a final location is determined,

the mounting bracket should be permanently fused with the tub during

production. This process involves covering the bracket with fiberglass.

Again, insure the threaded hole is protected during this process so no

material obstructs the threads/opening. The factory install is now complete.

Once the hot tub is installed by the dealer, the dealer can then install the

transducer. DO NOT SHIP WITH THE TRANSDUCERS ATTACHED. This

installation is done by placing the transducer's brass mounting nut onto

the threaded stud. Insuring not to crossthread the brass nut, gently turn

the transducer 5 to 6 complete revolutions. If you feel resistance, stop

immediately. CAUTION: DO NOT OVERTIGHTEN. Spin the jam nut on the

stud down to the brass nut and, using two wrenches (one on the jam nut

and one on the brass nut), tighten the jam nut against the brass nut.

CAUTION: DO NOT TIGHTEN THE JAM NUT TO THE BRASS NUT

BY TURNING THE TRANSDUCER. THIS WILL RESULT IN SEVERE

DAMAGE TO THE TRANSDUCER AND WILL VOID THE WARRANTY.

You may now connect the wires to your amplifier (must be a 4 ohm stable

amp delivering 125-150 watts @ 4 ohms/speaker). Your install is complete.

Possible Locations

for Transducer and

Mounting Bracket