- ページ 15

カーアラーム Directed Security and Remote StartのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Directed Security and Remote Start 20 ページ。 Security and remote start

ページを印刷する

1. Wiring Diagram

Latch rear defogger: the output activates 10 seconds after start if the interior temperature is below 55F. It turns off after 10 minutes or

upon remote start off

Pulse rear defogger: the output activates (for 800mS) 10 seconds after start if the interior temperature is below 55F.

9. Anti-grind Output

•

On/Off: With the anti-grind On (default) the ground-when-armed output will be active during remote start operation. If accessories such

as a voice module or window module are added to the unit, it may be necessary to program this feature off..

10. Diesel Start Delay

Wait-to-start input: (-) input on the Grey/black (H2/7) WTS wire will delay the starter output until the ground ceases.

Timed 15/30/45 seconds: delays the starter output per the selected option, the WTS wire does not function.

11. Run Time (Timer Mode)

•

12, 3, 6, 9 Minutes: Selects the time in minutes that the system will operate the engine until the system "times out". This is the maximum

operation period and the system may be shut down using a shutdown at any time. Using the Bitwriter®, the run time can be pro-

grammed for any duration from 1-16 minutes.

12 Timer Mode

•

Timed Starts/Temperature Starts: The system will start every 3-hours (a maximum of 6 times) until canceled by the brake, hood, turning

on the ignition, or neutral safety shut-down wires. The temperature start mode will not start the vehicle unless the interior temperature of

the vehicle is less than 0 degrees F. The temperature start mode will exit after 18 hours.

13 Short Run/Turbo

•

1/3/5/10 Minutes: When turbo mode is activated, the engine will run for the duration set per the selected option.

Security features disable/enable

The system has the ability to function as a security/remote start system or keyless/remote start system by enabling or disabling security. The

default setting is Enabled.

To program the feature.

Open a door.

Turn the ignition on, then off.

Press and hold the valet button until the LED flashes 3 times and the siren (if connected) chirps 3 times.

Release the control center button.

Note: If the valet button is released and then pressed again, the system will enter the features programming menus.

Within 15 seconds, simultaneously press the

The siren (if connected) will chirp and the parking lights will flash as listed below

1 flash/chirp: Security features disabled

2 flashes/chirps: Security features enabled

Security Features Disabled will disable all security operations of the system, including but not limited to those listed below:

•

Multi Level Arming

•

Sensor Warn-away

•

Full Trigger Operation

Red 4-pin port, Bitwriter/ESP2 or D2D programming

The Red 4-pin plug may be configured as a Bitwriter/ESP2 or D2D port.

The factory default is Bitwriter/ESP2 mode.

To use as D2D mode follow the below steps:

Make sure White/Blue activation wire is grounded.

Power the unit up. The system LED flashes for 5 seconds to confirm D2D mode change.

Remove the White/Blue wire from ground.

To change from D2D to Bitwriter/ESP2 mode:

Make sure the White/Blue activation wire is grounded.

Power the unit up, the system LED turns on solid for 5 seconds to confirm Bitwriter/ESP2 mode change.

Remove the White/Blue wire from ground.

The procedure can be repeated to toggle from one mode to the other.

Important: If you power up the system with the White/Blue activation wire ungrounded, the system LED

will come on solid for 5 seconds indicating the system is in Bitwriter/ESP2 mode.

and

buttons of a programmed remote control.

DRW-226