- ページ 13

ロックス Directed XpressKit DBALLのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Directed XpressKit DBALL 19 ページ。 Ford5 remote start ready (rsr) installation
Directed XpressKit DBALL にも：インストレーション・マニュアル (16 ページ), マニュアル (14 ページ), インストレーション・マニュアル (16 ページ)

ページを印刷する

Platform: DBALL/DBALL2

Firmware: FORD5 Remote Start Ready (RSR) Installation

Feature & Option List

It is recommended to configure all the features and options listed below using the configuration tool found on the module

flashing page on www.directechs.com. The web offers more options such as RSR; however, manual configuration of the

features is possible using the information on this page.

* Default Option

Feat.

Operation

Flashes/Options

1. No RF Output*

RFTD Output

2. RFTD Output

Type

3. SmartStart

1. Disabled

2. Safelock

Smart OEM

Alarm Control

3. Enabled*

Feature Programming

To enter feature programming routine

Turn the ignition ON, then OFF.



Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the

Programming button.



The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate

the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will

repeat until a new command is entered.

Changing feature options

Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the



DBALL in RSR using 3x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to

change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will

change the option for the selected feature.

The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly



the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.

Accessing another feature

Press and release the programming button a number of times to advance from the current feature to the next desired feature.



The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to

indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.

When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.

Once a feature is programmed

Other features can be programmed.



The feature programming can be exited.

Exiting feature programming

No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming



sequence.



Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the

end of the programming sequence.

Module is connected to a remote starter using a standard installation.

Module is connected to an XL202 using an RSR or RXT installation (when available).

Module is connected to SmartStart using an RSR or RXT installation (when available).

The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command

will be executed at the beginning or end of the sequence; it must be controlled by the Remote

Starter.

Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will

unlock at the beginning of the sequence, and relock after start and shutdown.

Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm

the vehicle in the remote start sequence, only when required. The reason for this is, factory alarm

control must often be done by lock or unlock operation. This could create unnecessary actions

on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control will

monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle

is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Smart

OEM Alarm Control will also monitor the remote starter actions so that the factory alarm control is

not done twice. A remote starter, for which the Safelock feature is active, will work perfectly with

this option and will make it invisible to the user.

Description

Programming

Button

Rev.: 20160317

Page 13