- ページ 6
ツール Alemite 595-AのPDF サービスマニュアルをオンラインで閲覧またはダウンロードできます。Alemite 595-A 8 ページ。 Cordless grease gun
ページを印刷するSER 595-A
Specific Safety Rules
WARNING
The gun can develop high pressure up to
8,000 psi (552 bar). Rupture of components can
inject grease into skin and eyes, causing serious
injury and possible amputation. If injured, seek
immediate medical attention.
Do not operate without proper safety protection,
gloves, and goggles. Hold hose at spring guard
only. Do not use if hose is damaged or worn.
Inspect hose before each use. Use only Alemite
340067 Grease Whip Hose.
This gun uses lubricants, that may be flammable
and poisonous if ingested. Do not use gun near
open flame or other fire hazards. Read all
warnings on lubricants before using this gun.
Use ear protection to reduce the risk of induced
hearing loss.
Disconnect battery pack from gun before changing
accessories, storing gun or unscrewing grease
cylinder from the gun.
Ensure the switch is in the off position before
inserting battery pack. Inserting the battery
pack into power tools that have the switch on
invites accidents.
Never attempt to open the battery pack for
any reason.
Do not expose the battery pack to water.
Do not store the battery pack in locations where
the temperature may exceed 104°F (40°C).
Charge the battery pack only at ambient temperatures
between 40°F (4°C) and 104°F (40°C).
Warning! To reduce the risk of inj ury, the
user must read the instruction manual.
Separate collection. This product must not be
disposed of with normal household waste.
Loading and Priming the Gun
NOTE: Refer to Figure 2 for component
identification on the following procedures.
Cartridge Loading
1. Unscrew Grease Cylinder (30) from the gun.
2. Pull the follower rod and engage the groove in the
follower rod with the slot in the Grease Cylinder cap.
3. Remove the plastic cap from the cartridge.
Revision (05-12)
4. Apply a film of grease to the exposed inside surface of
the cartridge.
NOTE: This is only necessary for a virgin
gun.
5. Insert the cartridge into the Grease Cylinder.
• Remove the tabbed seal from the cartridge.
6. Screw the Grease Cylinder onto the gun.
7. Disengage the follower rod from the slot in the Grease
Cylinder cap.
• Push the follower rod into the Grease Cylinder.
Suction Loading
1. Unscrew Grease Cylinder (30) from gun.
2. Insert the head of the Grease Cylinder below the
surface of the grease.
3. Slowly pull the follower rod outward from the Grease
Cylinder cap until the groove is visible.
4. Engage the groove in the follower rod with the slot in
the Grease Cylinder's cap.
5. Screw the Grease Cylinder onto the gun.
6. Disengage the follower rod from the slot in the Grease
Cylinder cap.
• Push the follower rod into the Grease Cylinder.
Loader Pump
WARNING
The gun can be equipped with an optional
low-pressure Loader Fitting. Do not substitute with
a high-pressure grease fitting. Personal injury can
occur due to excessive pressure.
The use of a grease fitting will void the warranty.
CAUTION
The Loader Fitting on the gun must mate with the
loader coupler. The pump may not operate if the
components are not compatible.
1. Pull the follower rod and engage the follower by
rotating the rod.
2. Seat the Loader Fitting into the loader coupler.
• Push down to hold the coupler valve open.
3. Operate the pump and view the movement of the
follower rod.
6
Cordless Grease Gun
Alemite, LLC