- ページ 2

浄水器 Clarus 5000-0006のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Clarus 5000-0006 2 ページ。 Pressure effluent filter

ページを印刷する

Pressure Switch Installation P/N 5000-0006

1. Install the Pressure Switch in the upper part of the tank riser.

2. Attach the switch mount to the side of the riser. If the riser is plastic,

secure it with a SS screw. If the riser is cement, use a plastic anchor

and SS screw. Seal any holes through the riser.

3. Attach the switch

t o t h e m o u n t .

Secure with strap if

necessary.

4. Route the 1/4" tubing

down to the 1/4" port

on the filter or where

1/4" TUBE

the pressure is to be

monitored. Remove

the plug. Apply Teflon

tape to the male

threads on the 90°

fitting. Install the 90°

fitting in the 1/4" port.

Install the 1/4" tube

in the 90° fitting and

tighten to seal.

CAUTION

Be sure the tubing

does not interfere

with moving parts,

floats, valves, etc.

Manufacturer warrants, to the purchaser and subsequent owner during the warranty

period, every new product to be free from defects in material and workmanship under

normal use and service, when properly used and maintained, for a period of one year

from date of purchase by the end user, or 18 months from date of original manufacture

of the product, whichever comes first. Parts that fail within the warranty period, one

year from date of purchase by the end user, or 18 months from the date of original

manufacture of the product, whichever comes first, that inspections determine to be

defective in material or workmanship, will be repaired, replaced or remanufactured at

manufacturer's option, provided however, that by so doing we will not be obligated to

replace an entire assembly, the entire mechanism or the complete unit. No allowance

will be made for shipping charges, damages, labor or other charges that may occur

due to product failure, repair or replacement.

This warranty does not apply to and there shall be no warranty for any material or

product that has been disassembled without prior approval of manufacturer, subjected

to misuse, misapplication, neglect, alteration, accident or act of God; that has not

been installed, operated or maintained in accordance with manufacturer's installation

instructions; that has been exposed to outside substances including but not limited to

the following: sand, gravel, cement, mud, tar, hydrocarbons, hydrocarbon derivatives

(oil, gasoline, solvents, etc.), or other abrasive or corrosive substances, wash towels

or feminine sanitary products, etc. in all pumping applications. The warranty set out

All Clarus Environmental products must be installed and maintained in accordance with all applicable codes.

Product information presented here reflects conditions at time of publication. Consult factory regarding discrepancies or inconsistencies.

5. Route the wire safely

out of the tank with other

wires to the alarm. The

pressure switch can be

wired with a high level

float or on its own.

6. To adjust the switch:

A. Remove the 1/8" plug on

top of the switch and insert

the 7/32" hex wrench.

TO POWER

/ALARM

B. Start the pump. Let it

run for one minute to

allow the pipes to fill. If

1/4" PORT

the alarm sounds, turn

the switch adjustment

screw clockwise one turn

to increase the switch

resistance pressure.

Reset the alarm and repeat

this step until no alarm is triggered by the switch.

C. With the pump running and the alarm reset, turn the wrench

counter-clockwise until the alarm sounds (or lights). This is the

running pressure.

D. Now turn the wrench one full turn clockwise . This is approximately

3 psi above the running pressure. If nuisance tripping of the alarm

occurs, increase the switch resistance pressure by turning the switch

SK2208B

adjustment screw clockwise by small degrees until it stops.

E. IMPORTANT! Replace the 1/8" plug after adjusting the switch.

Limited Warranty

in the paragraph above is in lieu of all other warranties expressed or implied; and we

do not authorize any representative or other person to assume for us any other liability

in connection with our products.

Contact manufacturer at, 3649 Cane Run Road, Louisville, Kentucky 40211, Attention:

Customer Support Department to obtain any needed repair or replacement of part(s) or

additional information pertaining to our warranty.

MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL,

CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH OF EXPRESSED

OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE AND OF MERCHANTABILITY SHALL BE LIMITED TO THE

DURATION OF THE EXPRESSED WARRANTY.

Some states do not allow limitations on the duration of an implied warranty, so the above

limitation may not apply to you. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation or exclusion may not

apply to you.

This warranty gives you specific legal rights and you may also have other rights which

vary from state to state.

PRESSURE

SWITCH

WATERTIGHT

JUNCTION BOX

SK2208C

INCREASE

TO ALARM

PANEL

BLACK

WIRES

WHITE

WIRES

HIGH WATER

ALARM FLOAT

DECREASE

SK2208D