- ページ 2

水ポンプ ARO PP10A-XXX-XXX-A SeriesのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。ARO PP10A-XXX-XXX-A Series 12 ページ。 1" dry powder diaphragm pump

ページを印刷する

READ, UNDERSTAND AND FOLLOW THIS INFORMATION TO AVOID INJURY AND PROPERTY DAMAGE.

EXCESSIVE AIR PRESSURE

STATIC SPARK

EXCESSIVE AIR PRESSURE. Can cause per-

WARNING

sonal injury, pump damage or property damage.

Do not exceed the maximum inlet air pressure as

stated on the pump model plate.

Be sure material hoses and other components are able

to withstand fluid pressures developed by this pump.

Check all hoses for damage or wear. Be certain dispens-

ing device is clean and in proper working condition.

STATIC SPARK. Can cause explosion result-

WARNING

ing in severe injury or death. Ground pump and

pumping system.

Use the pump grounding screw terminal provided.

Use ARO® part no. 94829 ground kit or connect a suit-

able ground wire (12 ga. minimum) to a good earth

ground source.

Secure pump, connections and all contact points to

avoid vibration and generation of contact or static

spark.

Consult local building codes and electrical codes for

specific grounding requirements.

After grounding, periodically verify continuity of

electrical path to ground. Test with an ohmmeter from

each component (e.g., hoses, pump, clamps, contain-

er, spray gun, etc.) to ground, to ensure continuity.

Ohmmeter should show 0.1 ohms or less.

Submerse the outlet hose end, dispensing valve or

device in the material being dispensed if possible.

(Avoid free streaming of material being dispensed.)

Use hoses incorporating a static wire.

Use proper ventilation.

Keep inflammables away from heat, open flames and

sparks.

Keep containers closed when not in use.

Pump exhaust may contain contaminants.

WARNING

Can cause severe injury. Pipe exhaust away from work

area and personnel.

In the event of a diaphragm rupture, material can be

forced out of the air exhaust muffler.

Pipe the exhaust to a safe remote location when

pumping hazardous or inflammable materials.

Use a grounded 1" minimum ID hose between the

pump and the muffler.

HAZARDOUS PRESSURE. Can result in seri-

WARNING

ous injury or property damage. Do not service or

clean pump, hoses or dispensing valve while the sys-

tem is pressurized.

Disconnect air supply line and relieve pressure from

the system by opening dispensing valve or device and

/ or carefully and slowly loosening and removing out-

let hose or piping from pump.

HAZARDOUS MATERIALS. Can cause serious

WARNING

injury or property damage. Do not attempt to return

a pump to the factory or service center that contains

hazardous material. Safe handling practices must

comply with local and national laws and safety code

requirements.

Page 2 of 12

RELEASED 20/Feb/2019 12:56:22 GMT

OPERATING AND SAFETY PRECAUTIONS

HAZARDOUS MATERIALS

HAZARDOUS PRESSURE

Obtain Material Safety Data Sheets on all materials

from the supplier for proper handling instructions.

EXPLOSION HAZARD. Models containing alu-

WARNING

minum wetted parts cannot be used with 1,1,1-trichlo-

roethane, methylene chloride or other halogenated

hydrocarbon solvents which may react and explode.

Check pump motor section, fluid caps, manifolds and

all wetted parts to assure compatibility before using

with solvents of this type.

MISAPPLICATION HAZARD. Do not use mod-

WARNING

els containing aluminum wetted parts with food prod-

ucts for human consumption. Plated parts can contain

trace amounts of lead.

Verify the chemical compatibility of the

CAUTION

pump wetted parts and the substance being pumped,

flushed or recirculated. Chemical compatibility may

change with temperature and concentration of the

chemical(s) within the substances being pumped,

flushed or circulated. For specific fluid compatibility,

consult the chemical manufacturer.

Maximum temperatures are based on

CAUTION

mechanical stress only. Certain chemicals will signifi-

cantly reduce maximum safe operating temperature.

Consult the chemical manufacturer for chemical com-

patibility and temperature limits. Refer to PUMP DATA

on page 1 of this manual.

Be certain all operators of this equipment

CAUTION

have been trained for safe working practices, under-

stand it's limitations, and wear safety goggles / equip-

ment when required.

Do not use the pump for the structural sup-

CAUTION

port of the piping system. Be certain the system com-

ponents are properly supported to prevent stress on

the pump parts.

Suction and discharge connections should be flex-

ible connections (such as hose), not rigid piped,

and should be compatible with the substance being

pumped.

Prevent unnecessary damage to the pump.

CAUTION

Do not allow pump to operate when out of material

for long periods of time.

Disconnect air line from pump when system sits idle

for long periods of time.

Use only genuine ARO replacement parts to

CAUTION

assure compatible pressure rating and longest service

life.

Replacement warning labels are available

NOTICE

upon request: "Static Spark & Diaphragm Rupture"

pn \ 94080.

= Hazards or unsafe practices which

WARNING

could result in severe personal injury,

death or substantial property damage.

= Hazards or unsafe practices which

CAUTION

could result in minor personal injury,

product or property damage.

= Important installation, operation or

NOTICE

maintenance information.

PP10A-XXX-XXX-A (en)