- ページ 10
電動工具 ARO GV08A-03S-7のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。ARO GV08A-03S-7 12 ページ。 Sanders/polishers
MAINTENANCE SECTION
Assembly of the Throttle
1. Grasp the handle of the Motor Housing (1) in
copper-covered vise jaws, positioning the handle so
that the inlet end is upward.
Never install a used Throttle Valve Seat; always
install a new one.
2.
3.
4.
5.
6.
7.
If the Throttle Valve Seat (4) was removed, use a
flat-faced rod l/2" (13 mm) in diameter and about
6" (150 mm) long to press a new Throttle Valve Seat
into the handle until it seats.
While looking down through the bore of the Throttle
Valve Seat, insert the Throttle Plunger (6) until the
hole in the Plunger is centered beneath the hole in the
Throttle Valve Seat. Install Throttle Lever (5) by
aligning hole in the Throttle Lever with holes in
Motor Housing (1) and inserting Throttle Lever Pin
(5A).
Insert the Throttle Valve (8) so that the long-stem end
passes through the hole in the Throttle Plunger.
Insert the Throttle Valve Spring (9), small coil first, so
that the spring encircles the Throttle Valve.
Make certain the two Oiler Body Seals (11) are
positioned in the annular grooves on the Oiler
Body (10) and install the Oiler Body, counterbored
end first, into the handle. The large end of the
Throttle Valve Spring should seat in the counterbore
in the Oiler Body.
Thread the Inlet Bushing (7) into the bottom of the
handle and tighten it to a minimum 25 ft-lb
(33.9 Nm) torque.
8. Remove the Motor Housing from the vise.
Assembly of the Motor
1. If the Rear Rotor Bearing (3) was removed, install a
new one as follows:
a. Place the Bearing Nut (2) in the bore at the bottom
of the bearing recess in the Motor Housing (1).
b. Using a bearing inserting tool (see Drawing
TPD786) that has a pilot extending into the
Bearing, and a shoulder that contacts the outer
radius on the bearing shell, press the Rear Rotor
Bearing, unstamped end first, into the bearing
recess until it is about .010" (0.25 mm) below
flush.
c. Inject a little grease in the Bearing.
2. Slide the Front End Plate (21), flat side first, over the
splined end of the Rotor (18).
3. Using a sleeve that contacts only the inner ring of the
Front Rotor Bearing (23), press the Front Rotor
Bearing onto the splined hub of the Rotor until it seats
against the Front End Plate.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
The clearance between the Front End Plate and the
Rotor is critical.
While holding the Front End Plate, gently tap the
splined end of the Rotor until you can insert a 0.001"
feeler gauge or shim between the face of the Rotor
and End Plate.
Grasp the splined end of the Rotor in copper-covered
vise jaws so that the short hub of the Rotor is upward.
Wipe each Vane (19) with a film of the recommended
oil and place a Vane in each slot in the Rotor.
Place the Cylinder (20). air port end trailing, down
over the Rotor and against the Front End Plate.
Place the Rear End Plate (16), flat side first, over the
short hub of the Rotor.
Install the Rear End Plate Retainer (17) in the groove
on the rotor hub.
When installing the Rear End Plate Retainer (17),
make certain it does not fly as you slip it on the
huh of the Rotor.
Smear a film of the recommended grease on the Rear
End Plate Gasket (15) and place the Gasket on the
End Plate so that the port in the Gasket is aligned
with the port in the End Plate.
Using an assembly dowel 3/32" in diameter x 10"
long (2.3 mm x 254 mm), align the dowel groove in
the Front End Plate, Cylinder, Rear End Plate and
Gasket. Place the assembly rod in the aligned grooves
so that about 3" of the rod extends beyond the Rear
End Plate. Insert the extension in the dowel hole at
the bottom of the housing bore, and slide the motor
into the Motor Housing until it seats.
Withdraw the assembly dowel and insert the Cylinder
Dowel (22).
Place the two Bearing Spring Washers (26) inside the
Front Rotor Bearing Housing (24) and against the
Front Rotor Bearing Retainer (25).
Slide the Front Rotor Bearing Housing over the Front
Rotor Bearing.
Install the Exhaust Deflector Rear Seal (30) on the
Motor Housing.
Install the Exhaust Diffuser (29A) on the hub of the
Motor Housing.
10